OWC 16GB DDR4 3200MHz CL22 1.2V 260pin SODIMM Alienware X17 R1
- 16GB
- 260-Pin DDR4 Non-EC…
Prihvaćamo kriptovalute — tako kriptovalute koje posjedujete mogu kupiti pravi hardver.Plaćajte kriptovalutom, trošite je na pravi hardver. Besplatna osigurana dostava diljem svijeta iznad 399 $. Obični vanjski kartoni bez oznaka, otpremaju se iz Njemačke.Besplatna osigurana dostava iznad 399 $. Vaš je tečaj blokiran 30 minuta od otvaranja blagajne.Tečaj blokiran 30 minuta. Svaki je artikl zapečaćen, njegov serijski broj provjeren, i pokriven jamstvom od 24 mjeseca.Zapečaćen, jamstvo 24 mjeseca.
A-Tech
4GB DDR4 2400MHz desktop DIMM module running at 1.20V for AMD and Intel systems
This 4GB DDR4 2400MHz PC4-19200 DIMM is built for desktop computers that need a straightforward memory upgrade. It fits standard 288-pin slots and runs at the JEDEC-standard 1.2V, making it a direct replacement for the Hynix HMA451U6AFR8N-UH module. The single-rank 1Rx8 layout keeps installation simple for home users and system integrators alike. Builders who need more than 4GB per slot or who require ECC error correction should look elsewhere.
The decisive specification is the tested 2400MHz frequency at 1.20V, which determines whether the module matches the motherboard's supported memory profile. If the board only accepts lower speeds or different voltages, this stick will not operate as intended. No other timing or latency figures are supplied, so compatibility rests entirely on this speed and voltage match.
Every module undergoes quality-assurance testing before it ships, which reduces the chance of early failures during installation. A lifetime warranty covers the part for as long as you own it, and US-based technical support is available before, during, and after the purchase to help with compatibility checks or troubleshooting. No additional software or accessories are bundled with the memory.
| Brand | A-Tech |
|---|---|
| Capacity | 4GB |
| Speed | DDR4 2400 (PC4 19200) |
| Tested Frequency | 2400 |
| Voltage | 1.20V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Recommend Use | AMD & Intel Compatible |
The module uses the standard 288-pin DIMM form factor and runs at 1.20 V, which matches the DDR4 specification used by most desktop boards. Check your motherboard manual to confirm it supports DDR4 2400 non-ECC unbuffered memory.
Yes, provided your board has a free DDR4 DIMM slot and supports 4 GB modules. Mixing speeds is possible, but all modules will run at the speed of the slowest stick.
The product is listed as a compatible replacement for that exact Hynix part number, matching capacity, speed, voltage, and 1Rx8 organisation.
Također u ovoj kategoriji
Ista polica, ista blagajna — osam valuta i blokada tečaja na 30 minuta.
Ono što šaljete, i ono u čemu gledate cijene.
Poslano iz Vašeg novčanika na blagajni
Samo prikaz — katalog je izražen u dolarima
Nijedna valuta ne odgovara.
Odaberite jezik na kojem Vam se stranica obraća.
Novi ste ovdje?
Već imate račun?
Ne postoji automatsko resetiranje: ova trgovina ne šalje e-poštu, stoga ne postoji jednokratna poveznica koju biste mogli zatražiti. Ostavite adresu uz svoj račun, netko će je ručno obraditi.
Zahtjev zaprimljen
Ništa neće stići u Vaš pretinac e-pošte — ova trgovina uopće ne šalje e-poštu. Netko će to ručno preuzeti.
Sjetili ste se?