Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green circuit board with silver SFF-8654 connector and PCIe x8 gold fingers

Innocard

Innocard PCIe 4.0 x8 ReDriver SFF-8654 8i RAID controller

SKU CH-3S32-BZP37

Converts PCIe 4.0 x8 to SFF-8654 8i with integrated ReDriver and clock buffer for 16 GT/s signal extension over longer cables

  • TypePCIe 4.0
  • PCIe 4.0 x8 at 16 GT/s for high bandwidth
  • ReDriver extends Gen 4 signals over longer cables
  • Clock buffer drives 100 MHz across extended traces
  • SFF-8654 8i connector follows SFF-9402 Rev 1.1 pin-out
  • Green LED shows the add-in card is ready

PCIe 4.0 x8 ReDriver controller

This Innocard adapter converts a PCIe 4.0 x8 slot to an internal SFF-8654 8i connector using a built-in ReDriver. It is designed for server builders who need to extend Gen4 signals over longer cables or backplanes. The card includes clock, sideband and power-break buffers to maintain link integrity across extended trace lengths. A green LED indicates when the add-in card is ready.

SFF-8654 8i interface limits

The connector follows the SFF-9402 Rev 1.1 pin-out and carries eight lanes at 16 GT/s. Signal quality depends on cable construction and total trace length because the ReDriver compensates but cannot overcome fundamental physics. The 100 MHz clock buffer and bidirectional SMCLK/SMDAT repeaters help sustain the link, yet very long or poor-quality cables may still cause errors. No RAID processing or drive management is performed on this card.

Installation notes

The controller fits a standard PCIe x8 or x16 slot and requires no additional drivers for the ReDriver function. Builders must ensure the SFF-8654 cable pin-out matches the SFF-9402 Rev 1.1 specification to avoid miswired lanes. Common issues include loose SlimSAS latch engagement and exceeding the practical reach of the ReDriver with excessive cable daisy-chaining. Verify that the host platform routes PCIe 4.0 to the chosen slot.

Kohokohdat

  • PCIe 4.0 x8 at 16 GT/s for high bandwidth
  • ReDriver extends Gen 4 signals over longer cables
  • Clock buffer drives 100 MHz across extended traces
  • SFF-8654 8i connector follows SFF-9402 Rev 1.1 pin-out
  • Green LED shows the add-in card is ready

Tekniset tiedot

TypePCIe 4.0

Kysymyksiä tästä tuotteesta

Which SFF-8654 8i version should I select for my server?

This controller uses a single SFF-8654 8i connector pinned to SFF-9402 Rev 1.1, so choose the matching SlimSAS cable for eight lanes.

What does the 16GT/s headline figure mean once installed?

It indicates PCIe 4.0 x8 bandwidth at 16GT/s per lane, delivered through the on-board ReDriver and clock buffer for longer traces.

What interface standard does the card use and what does it cap in practice?

The card plugs into a PCIe 4.0 x8 slot and converts the signal to SFF-8654 8i, limited to eight lanes at 16GT/s.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.