Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
White 120mm square case fan with three-sided infinity mirror ARGB lighting and nine blades

Jungle Leopard

Jungle Leopard Prism6 MAX 120mm ARGB case fan White 1-pack

SKU CH-HHKZ-N0PP3

A 120 mm case fan with three-sided infinite-mirror ARGB lighting, hydraulic bearing and 800-1850 RPM speed range delivering 58.36 CFM at 29 dBA

  • Fan Counts1 Fan
  • TypeCase Fan
  • CompatibilityCase
  • Fan Size120mm
  • Fan Thickness25mm
  • Bearing TypeHydraulic Bearing

Color White Forward-1Pack

  • Three-sided infinite mirror ARGB lighting creates depth with 0.5 mm layered geometry
  • Balanced nine-blade design delivers 58.36 CFM airflow at 2.07 mmH₂O pressure
  • Hydraulic bearing and double-sided silicone pads keep noise at 29 dBA
  • PWM control spans 800 to 1850 RPM for flexible cooling curves
  • 5 V 3-pin ARGB and 4-pin PWM connectors enable motherboard synchronisation

White ARGB case fan with infinite-mirror lighting

The Jungle Leopard Prism6 MAX is a 120 mm PWM case fan finished in white with addressable RGB LEDs. Three-sided infinite-mirror panels create a layered light effect visible from the side and centre of the frame. A hydraulic bearing and double-sided silicone pads keep vibration low at the rated 29 dBA. The 5 V 3-pin ARGB header must be present on the motherboard or a separate controller is required for synchronised lighting.

Sustained airflow at 1850 RPM with hydraulic bearing

At the maximum 1850 RPM the fan delivers 58.36 CFM and 2.07 mmH₂O static pressure, figures that hold under continuous load rather than only in short bursts. The hydraulic bearing reduces wear during extended operation while the nine-blade geometry maintains pressure across radiators or dense mesh. Speed scales down to 800 RPM for quieter idle periods without losing bearing stability.

5 V ARGB header requirement limits plug-and-play use

The fan draws power from a standard 4-pin PWM connector but the ARGB signal needs a 5 V 3-pin header; boards lacking that connector cannot control the lighting without an external hub. No 12 V 4-pin RGB or proprietary ecosystem is supported, so compatibility must be checked before installation. The 25 mm thickness fits standard 120 mm mounting points in most chassis.

Kohokohdat

  • Three-sided infinite mirror ARGB lighting creates depth with 0.5 mm layered geometry
  • Balanced nine-blade design delivers 58.36 CFM airflow at 2.07 mmH₂O pressure
  • Hydraulic bearing and double-sided silicone pads keep noise at 29 dBA
  • PWM control spans 800 to 1850 RPM for flexible cooling curves
  • 5 V 3-pin ARGB and 4-pin PWM connectors enable motherboard synchronisation

Tekniset tiedot

BrandJungle Leopard
SeriesPrism6 MAX
ModelJL Prism6 MAX BK
Fan Counts1 Fan
TypeCase Fan
CompatibilityCase
Fan Size120mm
Fan Thickness25mm
Bearing TypeHydraulic Bearing
RPM1850RPM
Air Flow58.36CFM
Air Pressure2.07mmH20
Noise Level=29DBA
Power Connector3 / 4 Pin
ColorBlack / White
LEDARGB
Dimensions120×120×25mm 4.72*4.72*0.98in

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

How loud is the 1850 RPM fan during continuous all-day operation?

The fan runs at 29 dBA at maximum speed, so even at full 1850 RPM it stays quiet enough for a desk-side PC running all day.

Does my motherboard need a 5 V 3-pin ARGB header to use the lighting on this fan?

Yes — the lighting uses a 5 V 3-pin connector; without that header you will need a separate ARGB controller box to synchronise the effects.

Will the 120 mm mounting holes line up with my older case that only has 120 mm fan slots?

The fan is a standard 120 × 120 × 25 mm size, so it fits any chassis designed for 120 mm fans regardless of the case age.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.