Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Compact servo with metal gears, dual bearings, and status indicator light

LORDWORLD

LORDWORLD LX-16A Serial Bus Servo Dual Bearing Full Metal Gear 17kg.cm 240°

SKU CH-CBXR-FNCA9

Serial bus servo with dual ball bearings and full metal gears delivers 17 kg·cm torque at 7.4 V with 240° control angle and real-time position, temperature, voltage feedback

  • High torque for demanding robots with 17 kg/cm at 7.4 V
  • Real-time position, temperature and voltage feedback simplifies debugging
  • Warning light blinks on overcurrent, overtemperature or locked-rotor events
  • Full metal gears and dual ball bearings extend service life and accuracy
  • Daisy-chain serial wiring reduces I/O ports and keeps builds tidy

High-Torque Serial Bus Servo

The LORDWORLD LX-16A is a serial bus servo built with full metal gears and dual ball bearings. It delivers 17 kg.cm of torque at 7.4 V and 15 kg.cm at 6.6 V. Real-time feedback reports position, temperature and voltage, while a top-mounted warning light signals overcurrent, overheating or locked-rotor conditions. The control angle spans 240°.

Suited For Robot Builders And Makers

This servo suits hobbyists and developers assembling RC robots or DIY automation projects that need accurate positioning with simple daisy-chain wiring. The serial interface reduces the number of I/O ports required on the controller. Builders needing continuous rotation or a control range beyond 240° should look at other actuator types.

240° Control Angle With Serial Daisy-Chain

The single specification that decides fit is the 240° control angle combined with the serial bus daisy-chain topology. If your mechanism requires a wider rotation range or a traditional PWM connection, this unit will not match the mechanical or wiring requirements.

Kohokohdat

  • High torque for demanding robots with 17 kg/cm at 7.4 V
  • Real-time position, temperature and voltage feedback simplifies debugging
  • Warning light blinks on overcurrent, overtemperature or locked-rotor events
  • Full metal gears and dual ball bearings extend service life and accuracy
  • Daisy-chain serial wiring reduces I/O ports and keeps builds tidy

Tekniset tiedot

BrandLORDWORLD

Kysymyksiä tästä tuotteesta

What mounting dimensions does the LX-16A servo require?

The servo uses a standard serial bus dual-interface connector, allowing daisy-chain wiring from a single I/O port on the control board.

How do I install the LX-16A servo, and what step is often missed?

Connect the servo in series via the dual interface, then apply 6.6 V or 7.4 V; the top warning LED will blink if overcurrent, over-temperature or locked-rotor occurs, confirming correct setup.

What maintenance will the LX-16A servo need over time?

The full metal gears and dual ball bearings are rated for extended service life; monitor the real-time position, temperature and voltage feedback to detect wear early.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.