Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Two green DDR4 UDIMM sticks without heat spreaders

NEMIX RAM

NEMIX RAM 16GB (2x8GB) DDR4 2933MHz CL21 1.2V 288-Pin UDIMM memory upgrade

SKU CH-T0N3-7W4QP

16 GB dual-channel DDR4-2933 CL21 kit validated for Supermicro workstations

  • Capacity16GB (2 x 8GB)
  • SpeedDDR4 2933 (PC4 23400)
  • ECCNo
  • Buffered/RegisteredUnbuffered
  • ChipsetMajor OEM Samsung, Micron, Hynix
  • Voltage1.20V
  • 16 GB kit (2×8 GB) doubles system memory capacity
  • DDR4 2933 MT/s speed supports fast data throughput
  • CL21 latency timed for responsive operation
  • 2 V low voltage reduces power draw
  • 288-pin UDIMM fits compatible Supermicro boards

SuperMicro DDR4 2933MHz Kit

This 16GB kit contains two 8GB DDR4 UDIMM modules rated at 2933MHz with CL21 latency. It is built for SuperMicro desktop and SuperWorkstation motherboards such as the MBD-C9X299-PGF. The unbuffered, non-ECC design suits standard workstation workloads.

Upgrade from lower capacity or speed

Replacing a smaller DDR4 kit or slower modules adds bandwidth for multi-threaded applications and virtual machines. The jump is worth it when the board supports 2933MHz operation and the workload exceeds the current memory ceiling.

Check motherboard qualification list

Verify that the specific SuperMicro model accepts 1Rx8 288-pin UDIMMs at 1.2V without ECC. Confirm the number of available slots and the maximum supported capacity per slot before ordering.

Kohokohdat

  • 16 GB kit (2×8 GB) doubles system memory capacity
  • DDR4 2933 MT/s speed supports fast data throughput
  • CL21 latency timed for responsive operation
  • 2 V low voltage reduces power draw
  • 288-pin UDIMM fits compatible Supermicro boards

Tekniset tiedot

BrandNEMIX RAM
SeriesSuperMicro Server/Workstation Compatible Series Memory
ModelSuperMicro DDR4 2933MHZ Non-ECC Unbuffered UDIMM
Part NumberMD23400-818K2
Capacity16GB (2 x 8GB)
SpeedDDR4 2933 (PC4 23400)
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor OEM Samsung, Micron, Hynix
Voltage1.20V
Compatible SystemSupermicro
CAS LatencyCL21
Heat SpreaderNo
Type288-Pin DDR4 UDIMM
Rank1Rx8
FeaturesDDR4 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content16GB (2X8GB) DDR4 2933MHZ PC4-23400 1Rx8 1.2V CL21 288-PIN Non-ECC Unbuffered UDIMM KIT

Kysymyksiä tästä tuotteesta

Will the 288-pin DDR4 UDIMM modules fit my Supermicro motherboard's memory slots?

Yes, the 288-pin DDR4 UDIMM form factor matches standard desktop and workstation DIMM slots on compatible Supermicro boards.

What is the correct way to seat the two 8GB sticks so the system recognises the full 16GB kit?

Align the notch on each module with the slot key, press straight down until both side clips click, and populate the channels indicated in the motherboard manual.

Do these non-ECC unbuffered modules require any firmware updates or periodic re-seating over time?

No firmware updates are needed for the memory itself, and the gold-edge contacts do not require routine re-seating under normal operation.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.