Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green circuit board SODIMM module with black memory chips and gold edge connector

NEMIX RAM

NEMIX RAM 4GB DDR3 1333 PC3-10600 1.35V 204-Pin SODIMM POSIFLEX PS-3415 memory upgrade

SKU CH-W0Z3-5X80G

A 4GB DDR3 SODIMM module running at 1333MHz with CL9 latency for the POSIFLEX PS-3415 terminal

  • Capacity4GB
  • SpeedDDR3 1333 (PC3 10600)
  • ECCNo
  • Buffered/RegisteredUnbuffered
  • ChipsetMajor OEM Samsung, Micron, Hynix
  • Voltage1.50V
  • Designed for POSIFLEX PS-3415 terminal
  • DDR3 1333 speed for responsive operation
  • Low 1.35V voltage reduces power draw
  • 4GB capacity handles daily POS workloads
  • 204-pin SODIMM fits the memory slot

POS Terminal Memory Upgrade

This 4 GB DDR3 SODIMM is built specifically for the POSIFLEX PS-3415 fanless touch-screen terminal. It uses a 204-pin unbuffered non-ECC layout running at 1333 MHz with CL9 latency. The module draws 1.35 V and is tested for stable operation in point-of-sale workloads.

Thermals and Power in Service

Low-voltage 1.35 V operation keeps heat output minimal inside the sealed fanless chassis. No heat spreader is fitted, relying on the terminal's passive cooling design. Power draw stays within the platform's original memory budget, so the upgrade does not increase acoustic or thermal load.

When the Upgrade Makes Sense

Replacing a smaller 2 GB stick or adding a second module doubles the memory available to the POS application and operating system. The jump is worth it when the terminal runs multiple peripherals or newer software that exceeds the original capacity. Builders needing ECC or registered memory should look elsewhere.

Kohokohdat

  • Designed for POSIFLEX PS-3415 terminal
  • DDR3 1333 speed for responsive operation
  • Low 1.35V voltage reduces power draw
  • 4GB capacity handles daily POS workloads
  • 204-pin SODIMM fits the memory slot

Tekniset tiedot

BrandNEMIX RAM
SeriesPOSIFLEX POS Series Point of Sale Kiosk Memory
ModelPOSIFLEX POS DDR3 1333MHZ Non-ECC Unbuffered SODIMM
Part NumberMS10600-428K1
Capacity4GB
SpeedDDR3 1333 (PC3 10600)
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor OEM Samsung, Micron, Hynix
Voltage1.50V
Compatible SystemPOSIFLEX POS
CAS LatencyCL9
Heat SpreaderNo
Type204-Pin DDR3 SODIMM
Rank2Rx8
FeaturesDDR3 Non-ECC Unbuffered SODIMM Motherboard Compatible
Package Content4GB (1X4GB) DDR3 1333MHZ PC3-10600 2Rx8 1.35V 204-PIN Non-ECC Unbuffered SODIMM

Kysymyksiä tästä tuotteesta

How do I install this 204-pin SODIMM into the POSIFLEX PS-3415?

Power off the terminal, open the memory compartment, align the notch on the module with the slot key, insert the module, and press down until the retaining clips lock it in place.

Will this CL9 DDR3 1333 module need replacement due to wear?

Solid-state memory has no moving parts, so it does not wear out under normal use; replacement is only needed if a fault develops or capacity requirements change.

What limits sustained throughput on this PC3-10600 stick?

The DDR3 1333 interface caps maximum bandwidth at the PC3-10600 rating, so continuous heavy workloads will hit that ceiling first.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.