BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.
NEMIX RAM
4GB DDR4 2400 CL17 1.2V SODIMM module for QNAP NAS, laptop, AIO or SFF upgrades
This 4 GB DDR4 module runs at 2400 MT/s with CL17 latency and 1.20 V operation. The 260-pin unbuffered non-ECC SO-DIMM fits laptops, all-in-one PCs, small-form-factor systems and compatible NAS devices. It is built for straightforward capacity upgrades in those platforms.
Operating at the standard 1.20 V DDR4 voltage keeps power draw low and heat output minimal during typical workloads. The module has no heat spreader, relying on the system’s existing airflow for cooling. Silent operation is maintained because there are no moving parts on the memory itself.
All modules are rigorously stress tested under load to ensure reliability during extended use. The unbuffered non-ECC design delivers consistent throughput for long-running NAS services, virtual machines or compilation tasks. Stability is validated for continuous operation rather than short bursts alone.
| Brand | NEMIX RAM |
|---|---|
| Series | NEMIX RAM DDR4 Orignial Series 260-Pin NON-ECC Unbuffered SODIMM Memory |
| Model | DDR4 NON-ECC Unbuffered SODIMM Laptop, AIO, SFF, NAS Storage Device Memory |
| Part Number | MS19200-418K1 |
| Capacity | 4GB |
| Type | 260-Pin DDR4 SO-DIMM |
| Speed | DDR4 2400 (PC4 19200) |
| CAS Latency | CL17 |
| Voltage | 1.20V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Heat Spreader | No |
| Features | DDR4 Laptop, AIO All-in-One, SFF, NAS Device Compatible |
Power off the NAS, open the memory cover, align the notch on the module with the slot key, press firmly until the side clips click, then replace the cover before powering on.
No scheduled maintenance is required; the module has no heat spreader and runs at 1.20V, so only replace it if a memory test reports errors or you need more capacity.
The 4GB capacity is the first bottleneck; once the NAS uses all available memory it must swap to disk, which slows performance long before thermal or voltage limits are reached.
Myös tällä osastolla
Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.
Valuutta, jolla maksetaan, sekä valuutta, jossa hinnat näytetään.
Lähetetään lompakostasi kassalla
Vain näyttöä varten — hinnat ovat Yhdysvaltain dollareissa
Valuuttaa ei löytynyt.
Valitse kieli, jolla sivusto puhuu sinulle.
Ei vastaavaa kieltä.
Uusi täällä?
Onko sinulla jo tili?
Automaattista palautusta ei ole: kauppa ei lähetä sähköpostia lainkaan, joten kertakäyttöistä linkkiä ei ole mistä pyytää. Jätä osoite tilille, niin se käsitellään käsin.
Pyyntö kirjattu
Mikään ei ole tulossa sähköpostiisi — tämä kauppa ei lähetä sähköpostia lainkaan. Joku käsittelee nämä pyynnöt käsin.
Muistitko sen?