Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green printed circuit board with black memory chips and gold edge connector

NEMIX RAM

NEMIX RAM 96GB DDR5 5600 CL46 2Rx4 1.1V ECC RDIMM Supermicro H13DSG-OM memory upgrade

SKU CH-H42B-5JP26

96 GB DDR5 5600 RDIMM with ECC and registered buffering for Supermicro H13DSG-OM

  • Capacity96GB
  • Type288-Pin DDR5 RDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCYes

Size 96GB

Näytä 30 muuta kokoonpanoa
  • 96 GB capacity expands server memory headroom
  • DDR5 5600 speed matches the board's rated frequency
  • CL46 CAS latency meets the controller's timing requirement
  • 2Rx4 registered ECC design enables full-slot population with error correction
  • 1 V operation aligns with the motherboard's voltage spec

Exact-match DDR5 upgrade for Supermicro H13DSG-OM

This 96GB DDR5 5600 CL46 kit is built to the Supermicro H13DSG-OM motherboard's memory-population rules. The 2Rx4 registered ECC RDIMM format matches the board's 288-pin slots so the controller recognises the full capacity at rated speed. It is not a UDIMM or SODIMM alternative. Buyers who need a different rank, voltage or form factor should verify their manual first.

Thermals noise and power draw in normal use

Operating at 1.1V, the modules draw minimal power and run without a heat spreader. Registered buffering reduces electrical load on the memory controller when every slot is populated. ECC corrects single-bit errors on the fly, preventing silent data corruption and unplanned reboots. No active cooling is included or required by the specification.

Build quality connectors and day-to-day implications

Major OEM chips from Samsung Micron or Hynix provide enterprise-grade stability for fully populated servers. The 288-pin RDIMM keying prevents mis-installation in incompatible slots. Lifetime replacement warranty and US-based technical support back the upgrade. Installers must follow the motherboard manual for approved DIMM population order and maximum supported capacity per channel.

Kohokohdat

  • 96 GB capacity expands server memory headroom
  • DDR5 5600 speed matches the board's rated frequency
  • CL46 CAS latency meets the controller's timing requirement
  • 2Rx4 registered ECC design enables full-slot population with error correction
  • 1 V operation aligns with the motherboard's voltage spec

Tekniset tiedot

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Server Memory
ModelDDR5 ECC RDIMM Registered Server Memory
Part NumberMR44800-9624K1
Capacity96GB
Type288-Pin DDR5 RDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCYes
Buffered/RegisteredRegistered
Rank2Rx4
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 ECC RDIMM Motherboard Compatible
Package Content96GB DDR5 5600MHz PC5-44800 2Rx4 1.1V 288-PIN ECC RDIMM KIT

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

How do I install the 288-pin DDR5 RDIMM in the Supermicro H13DSG-OM and what step is often missed?

Power down the server, open the chassis, and insert the module into the DIMM slot specified by the motherboard manual for your CPU configuration; the step most often missed is following the exact population order required for 2Rx4 registered DIMMs so the memory controller initialises all 96GB at 5600MHz.

What maintenance or replacement will this 96GB DDR5 ECC RDIMM need over its service life?

No routine maintenance is required for the module itself; ECC corrects single-bit errors automatically, but if a DIMM develops uncorrectable errors the server will log the fault and the affected stick must be replaced to restore full redundancy.

What limit appears first when the 1.1V CL46 registered memory runs sustained workloads on the H13DSG-OM?

The memory controller's maximum supported capacity per channel and the board's qualified voltage limit of 1.1V are reached before thermal throttling, so full-speed operation depends on staying within the validated population rules.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.