Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Two green DDR5 RDIMM sticks, no heat spreaders, 288-pin gold contacts, 64GB kit

NEMIX RAM

NEMIX RAM DDR5 5600 64GB (2x32GB) ECC RDIMM CL46 1.1V Supermicro H13SVW-NT memory upgrade

SKU CH-EX38-A2MVR

64 GB DDR5 kit in two 32 GB registered ECC RDIMMs at 5600 MT/s, CL46, 1.1 V, 288-pin, built for Supermicro H13SVW-NT servers

  • Capacity64GB (2 x 32GB)
  • Type288-Pin DDR5 RDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCYes

Size 64GB 2X32GB

Näytä 12 muuta kokoonpanoa

Speed 5600MHz

  • 64 GB total capacity delivered in a matched 2 × 32 GB kit
  • DDR5 5600 MT/s speed runs at the server's rated data rate
  • Registered ECC design with CL46 timing corrects single-bit errors for uptime
  • 1 V operation matches the platform's specified voltage for stable population
  • 288-pin RDIMM form factor fits the Supermicro H13SVW-NT memory slots

Exact-match DDR5 upgrade for Supermicro H13SVW-NT

This 64 GB kit delivers two 32 GB DDR5 5600 RDIMMs built to the motherboard's precise rank, voltage and timing requirements. Registered ECC architecture ensures the memory controller recognises every module at full capacity and rated speed. It is intended for administrators upgrading a compatible Supermicro server. Builders using desktop boards or unbuffered memory slots cannot use this kit.

Registered ECC stability

The registered design buffers address and command signals so all slots stay stable when fully populated. ECC corrects single-bit errors on the fly, preventing silent data corruption and unplanned reboots in production workloads. Modules operate at 1.1 V without a heat spreader, relying on server chassis airflow. The 288-pin connector matches the board's DDR5 RDIMM slots exactly; UDIMM or SODIMM alternatives will not fit.

5600 MT/s CL46 2Rx8 specification decides fit

The kit runs at DDR5 5600 (PC5-44800) with CAS latency 46 and a dual-rank 2Rx8 organisation. This single spec set determines whether the memory controller will initialise at rated speed and full capacity. Consult the motherboard manual for approved DIMM population order and maximum supported capacity before purchase. Buyers needing different speeds, ranks or voltages must select another part.

Kohokohdat

  • 64 GB total capacity delivered in a matched 2 × 32 GB kit
  • DDR5 5600 MT/s speed runs at the server's rated data rate
  • Registered ECC design with CL46 timing corrects single-bit errors for uptime
  • 1 V operation matches the platform's specified voltage for stable population
  • 288-pin RDIMM form factor fits the Supermicro H13SVW-NT memory slots

Tekniset tiedot

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Server Memory
ModelDDR5 ECC RDIMM Registered Server Memory
Part NumberMR44800-328K2
Capacity64GB (2 x 32GB)
Type288-Pin DDR5 RDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCYes
Buffered/RegisteredRegistered
Rank2Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 ECC RDIMM Motherboard Compatible
Package Content64GB 2X32GB DDR5 5600MHz PC5-44800 2Rx8 1.1V 288-PIN ECC RDIMM KIT

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

Does DDR5 5600 PC5-44800 run at 5600 MT/s on the Supermicro H13SVW-NT?

Yes. The kit is rated DDR5 5600 (PC5-44800) and the motherboard's memory controller is designed to operate registered ECC RDIMMs at that speed when populated per the manual.

What physical slot and module height does the 288-pin RDIMM need on the H13SVW-NT?

The board uses standard 288-pin DDR5 RDIMM sockets. These modules have no heat spreader, so they fit the regular DIMM height clearance defined by the server chassis.

Which DIMM slots do I populate first for a 2x32 GB kit on the H13SVW-NT?

Consult the motherboard manual for the approved population order. Registered ECC RDIMMs must be installed in the sequence the manual specifies so the memory controller initialises all 64 GB at the rated 5600 MT/s.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.