NEMIX RAM DDR5-5600 2TB (16x128GB) ECC RDIMM CL46 1.1V Supermicro H14SST-G memory upgrade
- 2TB (16 x 128GB)
- 288-Pin DDR5 RDIMM
Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.
OWC
16 GB DDR4 2666 ECC unbuffered VLP DIMM for workstations, servers and NAS systems
This 16GB DDR4 module runs at 2666 MT/s with CL19 latency and 1.2V operation. It targets workstations, servers and NAS systems that require error-correcting code memory. The unbuffered 2Rx8 design fits standard 288-pin desktop slots without registration overhead. JEDEC and ROHS compliance ensures a warranty-safe upgrade path.
Operating at the standard 1.2V keeps power draw low and heat output minimal during typical workloads. No heat spreader is fitted, so the VLP profile relies on case airflow for cooling. The low voltage and absence of LEDs contribute to quiet, efficient operation in densely populated DIMM banks.
The module ships as a single 16GB DIMM with no extra cables, brackets or software utilities. OWC validates every stick in-house to meet or exceed OEM specifications for the listed Hynix and Micron part numbers. A limited lifetime warranty and free technical support back the upgrade, but no installation media or monitoring tools are included.
| Brand | OWC |
|---|---|
| Part Number | 2E6V42R816GB |
| Capacity | 16GB |
| Speed | DDR4 2666 (PC4 21300) |
| CAS Latency | CL19 |
| Voltage | 1.2V |
| ECC | Yes |
| Buffered/Registered | Unbuffered |
| Heat Spreader | No |
| Recommend Use | Workstations, Servers, and NAS Systems |
| LED Color | None |
Power off the system, open the case, align the notch on the 288-pin module with the slot key, press firmly until both retention clips click, then verify in BIOS that the module reports 16 GB at 2666 MT/s and ECC is enabled; the step most often missed is confirming ECC mode in firmware after the physical install.
No scheduled maintenance is required; keep interior dust-free and ensure the 1.2 V supply remains stable. If a correctable error count rises or the system logs uncorrectable ECC events, replace the module — otherwise it runs for the system life.
The JEDEC 1.2 V / CL19 timing ceiling is reached before thermal throttling; sustained write/read streams max out at the rated 2666 MT/s bandwidth, so throughput plateaus at the spec data rate rather than hitting a temperature wall.
Myös tällä osastolla
Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.
Valuutta, jolla maksetaan, sekä valuutta, jossa hinnat näytetään.
Lähetetään lompakostasi kassalla
Vain näyttöä varten — hinnat ovat Yhdysvaltain dollareissa
Valuuttaa ei löytynyt.
Valitse kieli, jolla sivusto puhuu sinulle.
Uusi täällä?
Onko sinulla jo tili?
Automaattista palautusta ei ole: kauppa ei lähetä sähköpostia lainkaan, joten kertakäyttöistä linkkiä ei ole mistä pyytää. Jätä osoite tilille, niin se käsitellään käsin.
Pyyntö kirjattu
Mikään ei ole tulossa sähköpostiisi — tämä kauppa ei lähetä sähköpostia lainkaan. Joku käsittelee nämä pyynnöt käsin.
Muistitko sen?