NEMIX RAM DDR5-5600 2TB (16x128GB) ECC RDIMM CL46 1.1V Supermicro H14SST-G memory upgrade
- 2TB (16 x 128GB)
- 288-Pin DDR5 RDIMM
Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.
OWC
8GB DDR4 3200 ECC registered RDIMM for server and workstation upgrades
This 8 GB DDR4 3200 module is built for workstations and servers that require registered ECC memory. It operates at PC4-25600 with a CL22 latency and runs at 1.2 V. The single-rank 1Rx8 design fits standard 288-pin RDIMM slots in compatible enterprise platforms.
The module follows JEDEC and RoHS standards without a heat spreader, keeping the profile low for dense server chassis. Registered buffering reduces electrical load on the memory controller, allowing larger total capacities in supported systems. ECC circuitry detects and corrects single-bit errors to protect data integrity.
This memory will not work in standard desktop computers or laptops that use unbuffered non-ECC DIMMs. It cannot be mixed with unbuffered modules in the same system. Check your motherboard or NAS documentation to confirm it accepts DDR4 3200 registered ECC RDIMMs before ordering.
| Brand | OWC |
|---|---|
| Part Number | 3R2D41R808GB |
| Capacity | 8GB |
| Type | 288-Pin DDR4 ECC RDIMM |
| Speed | DDR4 3200 (PC4 25600) |
| CAS Latency | CL22 |
| Voltage | 1.2V |
| ECC | Yes |
| Buffered/Registered | Registered |
| Rank | 1Rx8 |
| Heat Spreader | No |
The module runs at 3200 MT/s with CL22 timing; ECC and registered operation add one cycle of buffering, so sustained bandwidth is limited by the JEDEC PC4-25600 rating rather than raw frequency alone
It fits a standard 288-pin DDR4 DIMM socket; no heat spreader is present, so low-profile heatsinks or tight server chassis lids will not interfere with the bare PCB
Power down, open the retention clips, align the single key notch, press firmly until both clips snap shut, then verify in BIOS that ECC and registered modes are enabled — the missed step is confirming the memory mode after boot
Einnig í þessum vöruflokki
Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.
Það sem þú greiðir í, og það sem þú sérð verð í.
Sent úr veskinu þínu í greiðsluferlinu
Aðeins til skýringar — verð í vörulistanum eru í Bandaríkjadölum
Enginn gjaldmiðill passar við það.
Veldu tungumálið sem síðan talar við þig á.
Fyrsta heimsókn?
Áttu þegar aðgang?
Það er engin sjálfvirk endurstilling: þessi verslun sendir engan tölvupóst, svo það er enginn einnota tengill til að biðja um. Skildu netfangið eftir á aðganginum og einhver sinnir því handvirkt.
Beiðni skráð
Ekkert er á leiðinni í pósthólfið þitt — þessi verslun sendir engan tölvupóst. Einhver sinnir þessu handvirkt.
Mundir þú það?