Computer Memory Solutions
Computer Memory Solutions 8GB DDR3 1600MHz CL11 240-pin DIMM Optiplex 3020
8GB DDR3 1600MHz CL11 240-pin DIMM upgrade for Dell Optiplex 3020 desktop systems
- Capacity8GB
- Type240-Pin DDR3 SDRAM
- SpeedDDR3 1600 (PC3 12800)
- CAS LatencyCL11
- Timing11-11-11
- Voltage1.5V
- 8 GB capacity lets the OptiPlex 3020 reach its 16 GB maximum
- DDR3 1600 MHz speed matches the system's supported memory bus
- CL11 11-11-11 timing keeps latency low for responsive multitasking
- 5 V unbuffered non-ECC design fits the desktop's standard DIMM slots
- 240-pin 2Rx8 module installs directly into either of the two memory sockets
System-specific upgrade for Dell Optiplex 3020
This 8 GB DDR3 module is built to match the Optiplex 3020 desktop. It installs in a single 240-pin slot and runs at 1600 MHz with CL11 timing. The unbuffered, non-ECC design suits standard office workloads and general multitasking. Buyers who need ECC error correction or registered buffering should look elsewhere.
Standard voltage and passive cooling
The stick operates at the standard 1.5 V DDR3 voltage with no heat spreader attached. Power draw stays within normal DDR3 limits for an 8 GB dual-rank module. No active cooling is required and the board adds no audible noise to the system. Builders planning high-density arrays beyond two slots must verify motherboard limits independently.
Single-module kit with lifetime warranty
The package contains one 8 GB DIMM and no additional accessories or software. Computer Memory Solutions backs the module with a limited lifetime warranty when purchased directly from them. The lone stick leaves the second Optiplex 3020 slot free for a future upgrade. Systems requiring a matched pair out of the box will need a second identical unit.
Punti di forza
- 8 GB capacity lets the OptiPlex 3020 reach its 16 GB maximum
- DDR3 1600 MHz speed matches the system's supported memory bus
- CL11 11-11-11 timing keeps latency low for responsive multitasking
- 5 V unbuffered non-ECC design fits the desktop's standard DIMM slots
- 240-pin 2Rx8 module installs directly into either of the two memory sockets
Caratteristiche tecniche
| Brand | Computer Memory Solutions |
|---|---|
| Model | CM10246412800DIMM |
| Capacity | 8GB |
| Type | 240-Pin DDR3 SDRAM |
| Speed | DDR3 1600 (PC3 12800) |
| CAS Latency | CL11 |
| Timing | 11-11-11 |
| Voltage | 1.5V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Rank | 2Rx8 |
| Chipset | Major Brand Chipset |
| Heat Spreader | No |
| Compatible System | Dell Optiplex 3020 Destktop |
| Package Content | 1 Memory RAM Stick |
Domande su questo articolo
How do I install this 240-pin DDR3 DIMM into the Optiplex 3020, and what step is commonly missed?
Power off and unplug the desktop, open the case, align the notch on the module with the slot key, press firmly until both retention clips click shut, then verify 8GB appears in BIOS before closing the chassis.
Will this 1.5V unbuffered module need any firmware updates or component swaps later?
No firmware or driver updates are required for the memory itself; the module is a passive component with no moving parts and does not need scheduled replacement under normal operation.
What limit appears first when the Optiplex 3020 runs sustained workloads with this CL11 1600MHz stick?
The platform caps total memory at 16GB across two sockets, so adding a second 8GB module reaches the system maximum before bandwidth or latency becomes a bottleneck.
Anche in questo reparto
Anche i clienti hanno confrontato questi
Stesso reparto, stessa cassa — otto monete e un cambio bloccato per 30 minuti.



