BFKK
BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
US$ 214,99
0.00276429BTC
Op voorraad
NEMIX RAM
NEMIX RAM DDR5 6400MHz 32GB (2x16GB) CL52 1.1V ECC RDIMM Supermicro H14DST-F memory upgrade
A 32 GB DDR5-6400 registered ECC kit built for the Supermicro H14DST-F motherboard
- Capacity32GB (2 x 16GB)
- Type288-Pin DDR5 RDIMM
- SpeedDDR5 6400 (PC5 51200)
- CAS LatencyCL52
- Voltage1.10V
- ECCYes
- Exact DDR5-6400 PC5-51200 kit matches Supermicro H14DST-F spec for full-speed recognition
- Registered ECC RDIMM offloads controller and corrects single-bit errors for enterprise stability
- 2 x 16 GB 1Rx8 modules populate every slot at rated 1.1 V CL52 without downclocking
- 288-pin RDIMM form factor fits only the slots your motherboard requires
- Lifetime replacement warranty with US-based technical support included
Exact-match DDR5-6400 ECC RDIMM kit
This 32 GB kit contains two 16 GB DDR5-6400 modules built to the PC5-51200 standard. Each stick is a 288-pin registered DIMM with ECC, 1Rx8 organisation and CL52 latency at 1.10 V. It is validated for the Supermicro H14DST-F motherboard.
Upgrade from slower DDR5 or partial populations
Replacing lower-speed DDR5 or filling empty slots with this spec-matched kit lets the memory controller run every channel at the rated 6400 MT/s without down-clocking. The jump is worth it when your workloads need maximum registered-ECC bandwidth and the board's population rules call for 1Rx8 modules at 1.1 V.
Tool-free press-in install; verify population order
Modules seat with a straight vertical press until the ejector tabs click. The most common issue is ignoring the motherboard's required slot sequence, which can prevent the system from recognising the full 32 GB or from booting at all. Always consult the H14DST-F manual for the approved DIMM order before installation.
Pluspunten
- Exact DDR5-6400 PC5-51200 kit matches Supermicro H14DST-F spec for full-speed recognition
- Registered ECC RDIMM offloads controller and corrects single-bit errors for enterprise stability
- 2 x 16 GB 1Rx8 modules populate every slot at rated 1.1 V CL52 without downclocking
- 288-pin RDIMM form factor fits only the slots your motherboard requires
- Lifetime replacement warranty with US-based technical support included
Specificaties
| Brand | NEMIX RAM |
|---|---|
| Series | NEMIX RAM Original Series Server Memory |
| Model | DDR5 ECC RDIMM Registered Server Memory |
| Part Number | MR51200-618K2 |
| Capacity | 32GB (2 x 16GB) |
| Type | 288-Pin DDR5 RDIMM |
| Speed | DDR5 6400 (PC5 51200) |
| CAS Latency | CL52 |
| Voltage | 1.10V |
| ECC | Yes |
| Buffered/Registered | Registered |
| Rank | 1Rx8 |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Heat Spreader | No |
| Compatible System | Supermicro |
| Features | DDR5 ECC RDIMM Motherboard Compatible |
| Package Content | 32GB 2X16GB DDR5 6400MHz PC5-51200 1Rx8 1.1V 288-PIN ECC RDIMM KIT |
Vragen over dit artikel
Will these 288-pin DDR5 RDIMMs fit the Supermicro H14DST-F motherboard slots?
Yes, the kit is built to the 288-pin DDR5 RDIMM form factor that the H14DST-F requires; it is not a UDIMM or SODIMM and matches the board's registered-DIMM slot keying.
What is the correct installation order for the two 1Rx8 modules on the H14DST-F?
Install the first module in the primary slot for each memory channel as defined in the motherboard manual, then add the second module to the matching secondary slot; skipping the primary slot leaves the channel unpopulated and the system will not boot.
Does the 1.10V operating voltage mean I will need to replace these modules sooner than higher-voltage RAM?
No, 1.10V is the standard DDR5 voltage and the modules carry a lifetime replacement warranty, so no scheduled replacement is required under normal server operation.
Ook in deze afdeling
Klanten vergeleken ook
Dezelfde afdeling, dezelfde kassa — acht munten en een koers die 30 minuten vaststaat.
BFKK
BFKK 2U Micro ATX Rackmount 2×5.25" 4×3.5" Side 80mm Fan
- Rackmount
US$ 216,99
0.00279001BTC
Op voorraad
