Wij accepteren cryptovaluta — zo kunnen de munten die u bezit echte hardware kopen.Betaal in crypto, besteed het aan echte hardware. Gratis verzekerde verzending wereldwijd vanaf $399. Neutrale dozen zonder merk, verzonden vanuit Duitsland.Gratis verzekerde verzending vanaf $399. Uw koers wordt 30 minuten vastgezet zodra het afrekenen begint.Koers 30 minuten vastgezet. Elk artikel is verzegeld, het serienummer wordt gecontroleerd, en het valt onder 24 maanden garantie.Verzegeld, 24 maanden garantie.

Favoriete artikelen Inloggen
Green circuit board with black memory chips and gold edge connectors

OWC

OWC 4GB DDR4 2133MHz CL15 1.2V 288pin UDIMM for Dell OptiPlex 7040 SFF Tower

SKU CH-BT7Q-NYD9C

4GB DDR4 2133MHz CL15 UDIMM module designed for Dell OptiPlex 7040 SFF and Tower systems

  • Capacity4GB
  • Type288-Pin DDR4 Non-ECC UDIMM
  • SpeedDDR4 2133 (PC4 17000)
  • CAS LatencyCL15
  • Voltage1.2V
  • ECCNo
  • Boosts Dell OptiPlex 7040 SFF responsiveness with 4GB DDR4 2133MHz CL15 module
  • Meets JEDEC PC4-17000 standard for warranty-safe upgrade compatibility
  • Low 1.2V operation reduces power draw on Dell OptiPlex 7040 Tower
  • Unbuffered 288-pin UDIMM installs easily in supported Dell OptiPlex systems
  • Single-rank 1Rx8 Non-ECC design ensures stable everyday desktop performance

OWC 4GB DDR4 module for Dell OptiPlex 7040

This 4GB DDR4 2133MHz CL15 UDIMM is built for Dell OptiPlex 7040 SFF and Tower systems. It runs at 1.2V without ECC or a heat spreader. The single-rank 1Rx8 design meets JEDEC and RoHS standards for a warranty-safe upgrade.

Replacing slower or smaller DDR4 DIMMs

Swapping an existing 2133MHz stick for this module adds capacity while keeping the same speed and latency. The jump is worth it when your OptiPlex 7040 has a free 288-pin slot and the BIOS recognises non-ECC unbuffered memory at PC4-17000.

Check slot count and maximum memory first

Verify how many 288-pin UDIMM slots your 7040 SFF or Tower board provides and what total capacity it supports. This module is not for systems that require ECC, registered DIMMs, or a different DDR generation.

Pluspunten

  • Boosts Dell OptiPlex 7040 SFF responsiveness with 4GB DDR4 2133MHz CL15 module
  • Meets JEDEC PC4-17000 standard for warranty-safe upgrade compatibility
  • Low 1.2V operation reduces power draw on Dell OptiPlex 7040 Tower
  • Unbuffered 288-pin UDIMM installs easily in supported Dell OptiPlex systems
  • Single-rank 1Rx8 Non-ECC design ensures stable everyday desktop performance

Specificaties

BrandOWC
Part Number2U1D41R804GB
Capacity4GB
Type288-Pin DDR4 Non-ECC UDIMM
SpeedDDR4 2133 (PC4 17000)
CAS LatencyCL15
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemDell OptiPlex 7040 SFF
Dell OptiPlex 7040 Tower

Andere versies van dit model

Nog 5 in dezelfde serie

Dezelfde familie, met ander geheugen, andere koeler of kloksnelheid — vergelijk voordat u beslist.

Vragen over dit artikel

Will the 288-pin DDR4 UDIMM fit inside the Dell OptiPlex 7040 SFF chassis?

Yes, the module uses the standard 288-pin DDR4 UDIMM form factor that matches the memory slots in both the 7040 SFF and 7040 Tower systems.

What is the correct way to seat the module so the retention clips lock?

Align the notch on the gold edge with the key in the slot, press straight down with even pressure until both side clips snap into place automatically.

When should this 4GB DDR4 2133MHz CL15 stick be replaced or upgraded?

Replace it if memory diagnostics report errors, or upgrade when your workload regularly exceeds the installed capacity and the system starts paging to disk.

Ook in deze afdeling

Klanten vergeleken ook

Dezelfde afdeling, dezelfde kassa — acht munten en een koers die 30 minuten vaststaat.