Acceptăm criptomonede — astfel, criptomonedele pe care le dețineți pot cumpăra echipamente reale.Plătiți în cripto, cheltuiți-o pe echipamente reale. Livrare asigurată gratuită oriunde în lume peste 399 $. Cartoane neutre, fără marcă, expediate din Germania.Livrare asigurată gratuită peste 399 $. Cursul dumneavoastră este blocat timp de 30 de minute de la deschiderea paginii de plată.Curs blocat 30 de minute. Fiecare articol este sigilat, numărul de serie este verificat, iar produsul este acoperit de o garanție de 24 de luni.Sigilat, garantat 24 de luni.

Produse urmărite Conectare
SFF-8482 SAS to SATA adapter cable with 15-pin power connector

SMUGDESK

SMUGDESK SFF-8482 SAS to SATA Adapter Cable with 15Pin Power

SKU CH-WYFS-SPH5S

Connects SFF-8482 SAS drives to SATA motherboards with a 15-pin power port for 2.5-inch and 3.5-inch drives

  • Connect SAS drives to SATA motherboards using SFF-8482 interface
  • Independent 15Pin SATA power port delivers stable drive operation
  • Supports 2.5 and 3.5 inch SFF-8482 SAS hard drives
  • Shielded precision connectors reduce interference for reliable data transfer
  • Plug-and-play design works without drivers for quick setup

SAS-to-SATA conversion cable

This SMUGDESK adapter cable bridges SFF-8482 SAS hard drives to standard SATA motherboard ports. It targets technicians and hobbyists who need to read server disks on desktop or workstation boards without buying a dedicated SAS controller. The independent 15Pin SATA power connector supplies the drive directly from a PSU cable.

Unidirectional SFF-8482 limitation

The cable works only from an SFF-8482 SAS drive to a SATA host; it cannot make a SATA drive operate on a SAS controller. Signal integrity relies on the SATA host controller speaking the SAS-to-SATA protocol subset, so compatibility depends on the motherboard implementation rather than the adapter itself.

Dual form-factor support with power headroom

Both 2.5-inch and 3.5-inch SFF-8482 SAS HDDs are supported, drawing power from the separate 15Pin port to avoid detection failures. The design handles typical sustained reads for data recovery or storage testing, but it cannot overcome bandwidth ceilings or command-set differences inherent to the SATA interface.

Puncte forte

  • Connect SAS drives to SATA motherboards using SFF-8482 interface
  • Independent 15Pin SATA power port delivers stable drive operation
  • Supports 2.5 and 3.5 inch SFF-8482 SAS hard drives
  • Shielded precision connectors reduce interference for reliable data transfer
  • Plug-and-play design works without drivers for quick setup

Specificații

Nicio specificație publicată pentru acest articol deocamdată.

Întrebări despre acest articol

Should I get the 2.5-inch or 3.5-inch version of this SFF-8482 adapter?

One cable works with both 2.5 and 3.5 inch SFF-8482 SAS drives, so no separate version is needed.

Will this SFF-8482 adapter let my SAS drive run at full SATA speed on a desktop motherboard?

The cable passes SATA signals from the SAS drive to the motherboard port; actual throughput is limited by the drive and the SATA controller.

Does the 15Pin power port on this SFF-8482 adapter draw from the motherboard or the PSU?

The 15Pin port takes a standard SATA power cable from the PSU to supply the SAS drive directly.

Tot din acest raion

Clienții au comparat și acestea.

Același raion, aceeași finalizare a comenzii — opt monede și un curs blocat 30 de minute.