Prijímame kryptomeny — takže mince, ktoré držíte, môžete zameniť za skutočný hardvér.Plaťte v krypte, miňte ho na skutočný hardvér. Poistená doprava zadarmo po celom svete nad 399 $. Neutrálne kartóny bez potlače, odosielané z Nemecka.Poistená doprava zadarmo nad 399 $. Váš kurz je zablokovaný na 30 minút hneď po otvorení pokladne.Kurz zablokovaný na 30 minút. Každý produkt je zapečatený, jeho sériové číslo je overené a vzťahuje sa naň 24-mesačná záruka.Zapečatené, 24-mesačná záruka.

Sledované položky Prihlásiť sa
Small 35mm square 12V case fan with double ball bearing, 6300 RPM, 5.5 CFM airflow, 20 dB noise

Fans

Fans D03P-12TS3 35x35x10mm 12V 0.09A 6300RPM case fan

SKU CH-YQNS-46B45 MPN D03P-12TS3

Compact 35×35×10 mm axial fan spins at 6300 RPM delivering 5.5 CFM at 20 dB from a 12 V 0.09 A double ball bearing motor

  • Compact 35×35×10 mm frame fits tight spaces
  • Double ball bearing rated for 6300 RPM reliability
  • Quiet 20 dB operation at full speed
  • 12 V DC input with 3 V–13.5 V working range
  • Moves 5.5 CFM airflow for targeted cooling

Compact 35 mm axial fan for tight builds

This 35×35×10 mm axial fan runs on 12 V DC and draws 0.09 A for a rated 1.08 W. Double ball bearings support a 6300 RPM speed while noise stays at 20 dB. Airflow reaches 5.5 CFM across a 3 V to 13.5 V working range.

Suits space-constrained cooling, not high-flow needs

Builders fitting a 1U server, a small-form-factor PC or a GPU shroud will appreciate the slim 10 mm profile and low acoustic profile. Anyone needing substantial case airflow or radiator static pressure should look at larger fans with higher CFM ratings.

Drops into 35 mm mounts with two-wire power

The fan uses a standard two-pin 12 V connection and fits any 35 mm square mounting pattern. Its narrow frame leaves room for dense component layouts, while the wide voltage tolerance lets it run from regulated 12 V rails or fan controllers without extra circuitry.

Prednosti

  • Compact 35×35×10 mm frame fits tight spaces
  • Double ball bearing rated for 6300 RPM reliability
  • Quiet 20 dB operation at full speed
  • 12 V DC input with 3 V–13.5 V working range
  • Moves 5.5 CFM airflow for targeted cooling

Špecifikácie

Pre tento produkt zatiaľ nie sú zverejnené žiadne špecifikácie.

Otázky k tomuto produktu

What power connection must my board provide for the 12 V 0.09 A fan to run?

The fan requires a 12 V DC header that can supply at least 0.09 A; it will also operate anywhere between 3 V and 13.5 V.

Will the 35×35×10 mm frame and 5.5 CFM airflow fit the same mounting points as my existing 35 mm square fan?

Yes, the 35 mm square footprint matches standard 35 mm mounting holes, and the 10 mm thickness is the only dimension to verify against your chassis clearance.

How can I confirm the double ball bearing unit is spinning at the rated 6300 RPM after installation?

Monitor the fan header in BIOS or software; a steady reading near 6300 RPM with noise around 20 dB indicates correct operation.

Aj v tomto oddelení

Zákazníci tiež porovnávali

Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.