NEMIX RAM DDR5-5600 2TB (16x128GB) ECC RDIMM CL46 1.1V Supermicro H14SST-G memory upgrade
- 2TB (16 x 128GB)
- 288-Pin DDR5 RDIMM
Prijímame kryptomeny — takže mince, ktoré držíte, môžete zameniť za skutočný hardvér.Plaťte v krypte, miňte ho na skutočný hardvér. Poistená doprava zadarmo po celom svete nad 399 $. Neutrálne kartóny bez potlače, odosielané z Nemecka.Poistená doprava zadarmo nad 399 $. Váš kurz je zablokovaný na 30 minút hneď po otvorení pokladne.Kurz zablokovaný na 30 minút. Každý produkt je zapečatený, jeho sériové číslo je overené a vzťahuje sa naň 24-mesačná záruka.Zapečatené, 24-mesačná záruka.
JacobsParts Inc.
Adjustable step-up converter raises 4–32 V input to a regulated 5–35 V output at up to 2 A and 20 W with 94 % peak efficiency
The JacobsParts XL6009 module converts a lower DC input into a higher regulated output for electronics projects. It accepts 4 to 32 volts input and delivers 5 to 35 volts at up to 2 amps. The board suits hobbyists and engineers building custom power rails from batteries or automotive sources. Output must always exceed input voltage.
The integrated XL6009 IC includes over-temperature and over-current protection for continuous operation. Efficiency reaches up to 94 percent depending on the voltage differential between input and output. Switching runs at 400 kilohertz with output ripple below 50 millivolts and load regulation within 0.5 percent. The potentiometer may require up to 15 turns before the output voltage begins to change.
The PCB-mount form factor measures 40 by 20 by 12 millimetres and handles a maximum of 20 watts. Constant-voltage regulation makes it suitable for LED strips and modules but not for driving raw LEDs directly. Input range stops at 32 volts and output caps at 35 volts, so designs needing higher boost ratios fall outside the device capability.
| Brand | JacobsParts |
|---|---|
| Model | DCMOD-T |
| Type | Step-Up Voltage Regulator |
| Mounting Style | PCB Mount |
| Current Rating | 2 A |
| Power Rating | 20 W |
The XL6009 IC includes over-temperature protection and an integrated MOSFET. At up to 94% efficiency, only a small fraction of the 20 W maximum becomes heat. There are no moving parts, so the module is completely silent in operation.
You need a DC source between 4 V and 32 V — for example a 3.7 V lithium cell or a 12 V battery — plus a multimeter to set the potentiometer, which may require up to 15 turns before the output voltage changes.
The module operates at 400 kHz with output ripple below 50 mV. Sensitive analog circuits on the same rail may pick up switching noise, so add decoupling capacitors or a separate linear regulator for those legacy devices.
Aj v tomto oddelení
Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.
Mena, v ktorej platíte, a mena, v ktorej sa zobrazujú ceny.
Odoslané z vašej peňaženky na pokladni
Len na zobrazenie — katalóg je uvedený v dolároch
Žiadna mena nezodpovedá.
Vyberte jazyk, v ktorom s vami bude web komunikovať.
Ste tu prvýkrát?
Účet už máte?
Automatický reset hesla neexistuje: tento obchod neposiela žiadne e-maily, takže neexistuje jednorazový odkaz, o ktorý by ste mohli požiadať. Nechajte adresu na účte — niekto sa jej ujme ručne.
Žiadosť zaznamenaná
Do vašej schránky nič nepríde — tento obchod neposiela vôbec žiadne e-maily. Niekto sa o to postará ručne.
Spomenuli ste si?