Prijímame kryptomeny — takže mince, ktoré držíte, môžete zameniť za skutočný hardvér.Plaťte v krypte, miňte ho na skutočný hardvér. Poistená doprava zadarmo po celom svete nad 399 $. Neutrálne kartóny bez potlače, odosielané z Nemecka.Poistená doprava zadarmo nad 399 $. Váš kurz je zablokovaný na 30 minút hneď po otvorení pokladne.Kurz zablokovaný na 30 minút. Každý produkt je zapečatený, jeho sériové číslo je overené a vzťahuje sa naň 24-mesačná záruka.Zapečatené, 24-mesačná záruka.

Sledované položky Prihlásiť sa
Green rectangular circuit board with black GPIO header and silver Ethernet jack

LORDWORLD

LORDWORLD PoE HAT (H) 5V 5A 802.3 development board

SKU CH-SZTS-BB88C

Powers Raspberry Pi 5 or CM5 through a single Ethernet cable with IEEE 802.3af/at PoE, delivering 5 V 5 A via an isolated SMPS while fitting the official case and active cooler

  • Power and connect Pi 5 or CM5 via a single Ethernet cable
  • IEEE 802.3af/at compliant for use with PoE-enabled routers and switches
  • Isolated SMPS delivers stable 5 V 5 A output for reliable performance
  • Fits official Pi 5 case and works with the Active Cooler
  • Standard 40-pin GPIO header enables plug-and-play setup

PoE HAT for Raspberry Pi 5 and CM5

The LORDWORLD PoE HAT (H) is an IEEE 802.3af/at compliant add-on board that powers a Raspberry Pi 5 or Compute Module 5 through a single Ethernet cable. It targets makers, IoT developers and robotics builders who want to reduce cable clutter in deployments where PoE infrastructure already exists. The board draws power from compatible switches or injectors and converts it locally for the host device.

Sustained 5 V 5 A delivery via isolated SMPS

An isolated switched-mode supply regulates the output to 5 V at up to 5 A, maintaining stable voltage during continuous loads such as compute-intensive scripts or peripheral-heavy IoT workloads. The isolation barrier protects the Pi from ground-loop noise and voltage spikes on the Ethernet line. Thermal performance scales with the host board's own cooling solution rather than relying on active components on the HAT itself.

Plug-and-play 40-pin GPIO header

The standard 40-pin header aligns directly with the Pi 5 GPIO, allowing tool-free installation that seats inside the official Raspberry Pi 5 case and clears the official Active Cooler. No soldering or jumper configuration is required; the board is recognised automatically by the Pi firmware. Builds that use non-standard tall headers or third-party cases with reduced internal clearance may encounter mechanical interference.

Prednosti

  • Power and connect Pi 5 or CM5 via a single Ethernet cable
  • IEEE 802.3af/at compliant for use with PoE-enabled routers and switches
  • Isolated SMPS delivers stable 5 V 5 A output for reliable performance
  • Fits official Pi 5 case and works with the Active Cooler
  • Standard 40-pin GPIO header enables plug-and-play setup

Špecifikácie

BrandLORDWORLD

Otázky k tomuto produktu

Does the 5V 5A output stay cool and quiet when the HAT powers a Raspberry Pi 5 continuously?

The isolated switched-mode supply delivers 5V at 5A efficiently, so heat and fan noise remain low during all-day operation.

Which Raspberry Pi models and accessories must I already own for this HAT to work?

It requires a Raspberry Pi 5 or Compute Module 5 with a 40-pin GPIO header and a PoE-enabled switch or router to supply power over Ethernet.

Will the board fit inside the official Raspberry Pi 5 case while I keep my existing Active Cooler installed?

Yes, the compact design is built to sit inside the official Pi 5 case and works alongside the Pi 5 Active Cooler without interference.

Aj v tomto oddelení

Zákazníci tiež porovnávali

Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.