Prijímame kryptomeny — takže mince, ktoré držíte, môžete zameniť za skutočný hardvér.Plaťte v krypte, miňte ho na skutočný hardvér. Poistená doprava zadarmo po celom svete nad 399 $. Neutrálne kartóny bez potlače, odosielané z Nemecka.Poistená doprava zadarmo nad 399 $. Váš kurz je zablokovaný na 30 minút hneď po otvorení pokladne.Kurz zablokovaný na 30 minút. Každý produkt je zapečatený, jeho sériové číslo je overené a vzťahuje sa naň 24-mesačná záruka.Zapečatené, 24-mesačná záruka.

Sledované položky Prihlásiť sa
Two green DDR5 UDIMM modules with black chips, no heat spreaders

NEMIX RAM

NEMIX RAM 16GB (2x8GB) DDR5-5600 CL46 1Rx8 1.1V UDIMM for Supermicro X14SAE-F

SKU CH-XX6Y-9359J

16 GB DDR5-5600 CL46 dual-channel kit built with major OEM chips for the Supermicro X14SAE-F motherboard

  • Capacity16GB (2 x 8GB)
  • Type288-Pin DDR5 UDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCNo

Size 16GB 2X8GB

  • 16 GB dual-channel kit expands system memory for Supermicro X14SAE-F
  • DDR5-5600 CL46 timing delivers rated speed at 1.1 V
  • 288-pin UDIMM form factor matches the board's memory slots exactly
  • Built with Samsung, Micron or Hynix chips for tested stability
  • Lifetime replacement warranty with US-based technical support

Exact-fit DDR5-5600 kit for Supermicro X14SAE-F

This 16GB (2 x 8GB) DDR5-5600 CL46 UDIMM kit is built for the Supermicro X14SAE-F motherboard. It matches the board's required 288-pin unbuffered non-ECC form factor, 1Rx8 rank structure and 1.1V operating voltage so the memory controller recognises full capacity at rated speed.

Capacity and headroom at 5600 MT/s

Two 8GB modules give 16GB total, enough for mainstream desktop workloads, office suites and light content creation. The CL46 latency and 1.1V JEDEC standard voltage leave no manual tuning headroom; the kit runs at its rated 5600 MT/s without overclocking and will not scale beyond that speed on this platform.

Upgrade path from lower-capacity DDR5

The kit replaces a single 8GB DDR5-5600 module or a slower DDR5 kit, doubling capacity while keeping the same voltage and timing profile. The jump is worth it when the system shows memory pressure in multitasking or when the motherboard manual calls for a matched pair to enable dual-channel operation. Not suited for builds needing ECC, registered DIMMs or capacities above 16GB.

Prednosti

  • 16 GB dual-channel kit expands system memory for Supermicro X14SAE-F
  • DDR5-5600 CL46 timing delivers rated speed at 1.1 V
  • 288-pin UDIMM form factor matches the board's memory slots exactly
  • Built with Samsung, Micron or Hynix chips for tested stability
  • Lifetime replacement warranty with US-based technical support

Špecifikácie

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR5 Non-ECC Unbuffered UDIMM Memory
Part NumberMD44800-818K2
Capacity16GB (2 x 8GB)
Type288-Pin DDR5 UDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content16GB 2X8GB DDR5 5600MHz PC5-44800 1Rx8 1.1V 288-PIN Non-ECC UDIMM KIT

Ďalšie verzie tohto modelu

Ďalších 5 v tomto rade

Rovnaký rad, iná pamäť, chladič alebo frekvencia — porovnajte pred rozhodnutím.

Otázky k tomuto produktu

Will this DDR5-5600 1.10V kit run alongside any existing DDR5 modules I keep in the Supermicro X14SAE-F?

The Supermicro X14SAE-F supports DDR5 only, so any modules you keep must also be DDR5. Mixing kits with different speeds, timings, or voltages can prevent the system from posting or force all memory to run at the lowest common settings. For best stability, use identical 5600 MT/s CL46 1.10V 1Rx8 UDIMMs.

How can I verify the kit is running at DDR5-5600 CL46 1.10V after installation?

Enter the BIOS and check the memory information screen: it should report 5600 MT/s, CL46, and 1.10V. You can also run CPU-Z or a similar tool in the OS to confirm the SPD profile and real-time frequency, timings, and voltage match the rated 5600 PC5-44800 CL46 1.10V specification.

What is included in the box and do I need to buy anything else to install it?

The box contains the 16 GB (2 × 8 GB) DDR5-5600 CL46 1.10V 288-pin UDIMM kit only. No heat spreaders, cables, or tools are bundled. Installation requires a compatible DDR5 motherboard slot and, if desired, an anti-static wrist strap — nothing else is required.

Aj v tomto oddelení

Zákazníci tiež porovnávali

Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.