Prijímame kryptomeny — takže mince, ktoré držíte, môžete zameniť za skutočný hardvér.Plaťte v krypte, miňte ho na skutočný hardvér. Poistená doprava zadarmo po celom svete nad 399 $. Neutrálne kartóny bez potlače, odosielané z Nemecka.Poistená doprava zadarmo nad 399 $. Váš kurz je zablokovaný na 30 minút hneď po otvorení pokladne.Kurz zablokovaný na 30 minút. Každý produkt je zapečatený, jeho sériové číslo je overené a vzťahuje sa naň 24-mesačná záruka.Zapečatené, 24-mesačná záruka.

Sledované položky Prihlásiť sa
Green 204-pin DDR3 SODIMM module with black chips, no heat spreader

NEMIX RAM

NEMIX RAM 4GB DDR3 1333 PC3-10600 1.35V 204-Pin SODIMM POSIFLEX XT-5315 memory upgrade

SKU CH-W69Q-2T5SN

4 GB DDR3 SODIMM running at 1333 MHz and 1.35 V for the POSIFLEX XT-5315 terminal

  • Capacity4GB
  • SpeedDDR3 1333 (PC3 10600)
  • ECCNo
  • Buffered/RegisteredUnbuffered
  • ChipsetMajor OEM Samsung, Micron, Hynix
  • Voltage1.50V
  • Designed for POSIFLEX XT-5315 terminal compatibility
  • 4GB DDR3 1333MHz PC3-10600 capacity upgrade
  • Low-voltage 1.35V operation reduces power consumption
  • 204-pin SODIMM form factor fits POS systems
  • Tested with major OEM Samsung Micron Hynix chips

Targeted POS Terminal Upgrade

This 4GB DDR3 SODIMM is built for the POSIFLEX XT-5315 JIVA terminal and compatible point-of-sale systems. It delivers a direct memory increase for environments running retail, hospitality or kiosk workloads on legacy DDR3 platforms. The module suits IT teams maintaining existing fleets rather than builders specifying new hardware.

Standard SODIMM Build for Service Access

The 204-pin unbuffered stick uses major OEM chips from Samsung, Micron or Hynix and carries no heat spreader, keeping the profile thin for cramped service bays. Non-ECC operation matches the terminal's motherboard design, and the 2Rx8 organisation is the native configuration for this platform. Installation follows the usual SODIMM slot procedure without special tools.

Low-Voltage Operation in Fanless Chassis

Rated at 1.35V with a CL9 latency at 1333MHz, the module draws minimal power inside the passively cooled XT-5315 enclosure. The reduced voltage compared to standard 1.50V DDR3 limits heat output, helping the terminal stay silent during extended shifts. No active cooling is required on the memory itself.

Prednosti

  • Designed for POSIFLEX XT-5315 terminal compatibility
  • 4GB DDR3 1333MHz PC3-10600 capacity upgrade
  • Low-voltage 1.35V operation reduces power consumption
  • 204-pin SODIMM form factor fits POS systems
  • Tested with major OEM Samsung Micron Hynix chips

Špecifikácie

BrandNEMIX RAM
SeriesPOSIFLEX POS Series Point of Sale Kiosk Memory
ModelPOSIFLEX POS DDR3 1333MHZ Non-ECC Unbuffered SODIMM
Part NumberMS10600-428K1
Capacity4GB
SpeedDDR3 1333 (PC3 10600)
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor OEM Samsung, Micron, Hynix
Voltage1.50V
Compatible SystemPOSIFLEX POS
CAS LatencyCL9
Heat SpreaderNo
Type204-Pin DDR3 SODIMM
Rank2Rx8
FeaturesDDR3 Non-ECC Unbuffered SODIMM Motherboard Compatible
Package Content4GB (1X4GB) DDR3 1333MHZ PC3-10600 2Rx8 1.35V 204-PIN Non-ECC Unbuffered SODIMM

Otázky k tomuto produktu

Does the DDR3 1333 PC3-10600 interface limit this module to 1333 MT/s in a POSIFLEX XT-5315 terminal?

Yes, the module is rated DDR3 1333 (PC3-10600) and will run at that speed in the POSIFLEX XT-5315.

What physical slot and form factor are required to install this 204-pin SODIMM?

It fits a standard 204-pin DDR3 SODIMM slot; the terminal must accept 204-pin unbuffered SODIMMs.

What is the correct way to seat this 1.35 V SODIMM so the terminal recognises the full 4 GB?

Align the notch, insert at an angle, then press down firmly until both side clips click into the notches.

Aj v tomto oddelení

Zákazníci tiež porovnávali

Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.