BFKK
BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
US$214.99
0.00277711BTC
재고 있음
NEMIX RAM
NEMIX RAM 4GB DDR3 1333 PC3-10600 1.35V 204-Pin SODIMM POSIFLEX XT-5315 memory upgrade
4 GB DDR3 SODIMM running at 1333 MHz and 1.35 V for the POSIFLEX XT-5315 terminal
- Capacity4GB
- SpeedDDR3 1333 (PC3 10600)
- ECCNo
- Buffered/RegisteredUnbuffered
- ChipsetMajor OEM Samsung, Micron, Hynix
- Voltage1.50V
- Designed for POSIFLEX XT-5315 terminal compatibility
- 4GB DDR3 1333MHz PC3-10600 capacity upgrade
- Low-voltage 1.35V operation reduces power consumption
- 204-pin SODIMM form factor fits POS systems
- Tested with major OEM Samsung Micron Hynix chips
Targeted POS Terminal Upgrade
This 4GB DDR3 SODIMM is built for the POSIFLEX XT-5315 JIVA terminal and compatible point-of-sale systems. It delivers a direct memory increase for environments running retail, hospitality or kiosk workloads on legacy DDR3 platforms. The module suits IT teams maintaining existing fleets rather than builders specifying new hardware.
Standard SODIMM Build for Service Access
The 204-pin unbuffered stick uses major OEM chips from Samsung, Micron or Hynix and carries no heat spreader, keeping the profile thin for cramped service bays. Non-ECC operation matches the terminal's motherboard design, and the 2Rx8 organisation is the native configuration for this platform. Installation follows the usual SODIMM slot procedure without special tools.
Low-Voltage Operation in Fanless Chassis
Rated at 1.35V with a CL9 latency at 1333MHz, the module draws minimal power inside the passively cooled XT-5315 enclosure. The reduced voltage compared to standard 1.50V DDR3 limits heat output, helping the terminal stay silent during extended shifts. No active cooling is required on the memory itself.
주요 특징
- Designed for POSIFLEX XT-5315 terminal compatibility
- 4GB DDR3 1333MHz PC3-10600 capacity upgrade
- Low-voltage 1.35V operation reduces power consumption
- 204-pin SODIMM form factor fits POS systems
- Tested with major OEM Samsung Micron Hynix chips
사양
| Brand | NEMIX RAM |
|---|---|
| Series | POSIFLEX POS Series Point of Sale Kiosk Memory |
| Model | POSIFLEX POS DDR3 1333MHZ Non-ECC Unbuffered SODIMM |
| Part Number | MS10600-428K1 |
| Capacity | 4GB |
| Speed | DDR3 1333 (PC3 10600) |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Voltage | 1.50V |
| Compatible System | POSIFLEX POS |
| CAS Latency | CL9 |
| Heat Spreader | No |
| Type | 204-Pin DDR3 SODIMM |
| Rank | 2Rx8 |
| Features | DDR3 Non-ECC Unbuffered SODIMM Motherboard Compatible |
| Package Content | 4GB (1X4GB) DDR3 1333MHZ PC3-10600 2Rx8 1.35V 204-PIN Non-ECC Unbuffered SODIMM |
이 상품에 대한 질문
Does the DDR3 1333 PC3-10600 interface limit this module to 1333 MT/s in a POSIFLEX XT-5315 terminal?
Yes, the module is rated DDR3 1333 (PC3-10600) and will run at that speed in the POSIFLEX XT-5315.
What physical slot and form factor are required to install this 204-pin SODIMM?
It fits a standard 204-pin DDR3 SODIMM slot; the terminal must accept 204-pin unbuffered SODIMMs.
What is the correct way to seat this 1.35 V SODIMM so the terminal recognises the full 4 GB?
Align the notch, insert at an angle, then press down firmly until both side clips click into the notches.
이 진열대의 다른 상품
고객들이 함께 비교한 상품
같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.
