Prijímame kryptomeny — takže mince, ktoré držíte, môžete zameniť za skutočný hardvér.Plaťte v krypte, miňte ho na skutočný hardvér. Poistená doprava zadarmo po celom svete nad 399 $. Neutrálne kartóny bez potlače, odosielané z Nemecka.Poistená doprava zadarmo nad 399 $. Váš kurz je zablokovaný na 30 minút hneď po otvorení pokladne.Kurz zablokovaný na 30 minút. Každý produkt je zapečatený, jeho sériové číslo je overené a vzťahuje sa naň 24-mesačná záruka.Zapečatené, 24-mesačná záruka.

Sledované položky Prihlásiť sa
Black 60mm NIDEC blower fan with 3-pin connector

OEM Industries

OEM Industries D06F-12BS3 60mm CPU cooler

SKU CH-1NH8-RMYWR

60 mm NIDEC blower fan with 12 V 0.29 A three-pin connector for CPU cooling

  • ColorBlack
  • TypeFan only
  • Fan Size60mm
  • Bearing Type1 Ball, 1 Sleeve
  • LEDNo
  • NIDEC 6025 blower fan delivers focused airflow
  • 12 V 0.29 A power draw keeps energy use low
  • 60 × 25 mm frame fits tight 60 mm mounts
  • 3-pin connector enables simple motherboard control
  • Ball-and-sleeve bearing balances durability with quiet operation

60 mm NIDEC blower fan for compact systems

The OEM Industries D06F-12BS3 is a 60 mm square blower that mounts in tight chassis or on small heatsinks. It runs on 12 V and draws 0.29 A through a standard three-pin connector. The mixed ball-and-sleeve bearing keeps noise low while maintaining steady airflow.

Three-pin voltage control limits speed adjustment

The three-wire interface reports RPM to the motherboard but regulates speed by varying voltage, not PWM. Fan curves therefore step in larger increments and the minimum speed is higher than on four-pin headers. Headers that only supply a fixed 12 V will run the blower at full speed continuously.

Check header pin count

Verify that the target board or controller offers a three-pin header with voltage control if you want variable speed. Confirm the 60 mm screw pattern matches the heatsink or case cut-out you intend to use. The unit is a bare fan without brackets, adapters or LED lighting.

Prednosti

  • NIDEC 6025 blower fan delivers focused airflow
  • 12 V 0.29 A power draw keeps energy use low
  • 60 × 25 mm frame fits tight 60 mm mounts
  • 3-pin connector enables simple motherboard control
  • Ball-and-sleeve bearing balances durability with quiet operation

Špecifikácie

ModelD06F-12BS3
ColorBlack
TypeFan only
Fan Size60mm
Bearing Type1 Ball, 1 Sleeve
LEDNo

Otázky k tomuto produktu

Should I pick the 60mm 12V 0.29A model or a different size for my case?

The 60mm frame fits 6025 mounting holes; the 12V 0.29A rating matches a standard 3-pin header, so choose this version when your chassis or heatsink only accepts a 60mm fan.

What does the 0.29A current draw mean once the fan is installed?

At 12V the fan pulls 0.29A, giving roughly 3W of power use; the motherboard header supplies voltage to spin the blades, and speed changes as that voltage is lowered or raised.

How does the 3-pin connector limit control compared to a 4-pin PWM header?

The 3-pin plug carries power, ground and a tachometer signal; the board can only vary voltage to adjust speed, it cannot send a PWM duty-cycle signal for finer low-speed control.

Aj v tomto oddelení

Zákazníci tiež porovnávali

Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.