Prijímame kryptomeny — takže mince, ktoré držíte, môžete zameniť za skutočný hardvér.Plaťte v krypte, miňte ho na skutočný hardvér. Poistená doprava zadarmo po celom svete nad 399 $. Neutrálne kartóny bez potlače, odosielané z Nemecka.Poistená doprava zadarmo nad 399 $. Váš kurz je zablokovaný na 30 minút hneď po otvorení pokladne.Kurz zablokovaný na 30 minút. Každý produkt je zapečatený, jeho sériové číslo je overené a vzťahuje sa naň 24-mesačná záruka.Zapečatené, 24-mesačná záruka.

Sledované položky Prihlásiť sa
Black 92mm sleeve bearing cooling fan with two wires

OEM Industries

OEM Industries JF0925S1M 92mm Sleeve Bearing Fan

SKU CH-HBPM-PYRDK

A 92mm sleeve-bearing DC fan with a 2-wire 12V 0.20A connection for targeted component cooling

  • ColorBlack
  • TypeFan only
  • Fan Size92mm
  • Bearing TypeSleeve Bearing
  • Power Connector2 Wires
  • LEDNo
  • 92 mm frame fits compact CPU cooler builds
  • Sleeve bearing keeps acoustic profile low for quiet operation
  • 12 V 0.20 A draw limits power budget impact
  • Two-wire connector simplifies installation on standard headers
  • Black finish blends cleanly with dark-themed builds

92 mm Sleeve Bearing Replacement Fan

This 92 mm sleeve bearing fan suits builders who need a direct replacement for a JF0925S1M cooler. It runs on a 12 V two-wire connection and draws 0.20 A. The black frame matches most standard CPU air coolers. It is not for buyers who need PWM speed control or a three-pin header.

Thermals Noise and Power Draw

The sleeve bearing keeps acoustic output low during typical desktop workloads. At 0.20 A the fan draws minimal power from the 12 V rail. No LED lighting means no extra current draw or visual distraction inside the case. The two-wire design reports no speed signal to the motherboard.

Sustained Load Behaviour

Under continuous load the sleeve bearing maintains consistent rotation without the rattle that can develop in some ball-bearing units. The fixed-voltage design keeps airflow steady rather than ramping with temperature. Builders who want automatic fan curves should choose a PWM model instead.

Prednosti

  • 92 mm frame fits compact CPU cooler builds
  • Sleeve bearing keeps acoustic profile low for quiet operation
  • 12 V 0.20 A draw limits power budget impact
  • Two-wire connector simplifies installation on standard headers
  • Black finish blends cleanly with dark-themed builds

Špecifikácie

ModelJF0925S1M
ColorBlack
TypeFan only
Fan Size92mm
Bearing TypeSleeve Bearing
Power Connector2 Wires
LEDNo

Otázky k tomuto produktu

How do I mount the 92 mm JF0925S1M fan, and which step often goes wrong?

Line up the four corner holes with your chassis or heatsink, insert the screws diagonally and tighten evenly; the common mistake is over-tightening one corner first, which warps the frame and adds vibration.

What maintenance will the sleeve bearing need later?

Sleeve bearings run on a thin oil film that gradually dries; when the fan becomes noisy or rpm drops, the only fix is to replace the whole unit.

What limit appears first during continuous 12 V operation?

The 0.20 A sleeve-bearing motor hits its thermal and wear ceiling before the wiring or connector does, so sustained load eventually degrades spin speed and acoustics.

Aj v tomto oddelení

Zákazníci tiež porovnávali

Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.