Prijímame kryptomeny — takže mince, ktoré držíte, môžete zameniť za skutočný hardvér.Plaťte v krypte, miňte ho na skutočný hardvér. Poistená doprava zadarmo po celom svete nad 399 $. Neutrálne kartóny bez potlače, odosielané z Nemecka.Poistená doprava zadarmo nad 399 $. Váš kurz je zablokovaný na 30 minút hneď po otvorení pokladne.Kurz zablokovaný na 30 minút. Každý produkt je zapečatený, jeho sériové číslo je overené a vzťahuje sa naň 24-mesačná záruka.Zapečatené, 24-mesačná záruka.

Sledované položky Prihlásiť sa
Compact black standalone duplicator with blue LCD, two SATA drive bays, tablet-sized frame

VinPower

VinPower HDDMINIDUP-2 duplicator, 2 target SATA 2.5 3.5 128MB DDR2

SKU CH-85M0-1F7WW MPN HDDMINIDUP-2

Standalone SATA duplicator clones up to two 2.5 or 3.5 inch drives simultaneously at 90 MB/s with 128MB DDR2 buffer and DoD erase

  • TypeHard Drive Duplicator
  • Target1 to 2
  • Buffer Memory128MB DDR2
  • Language SupportEnglish, Spanish, French, German, Italian, Japanese, and mor
  • Display20 x 2 Blue LCD
  • Operating TypeStandalone
  • Standalone operation needs no PC attached
  • 90 MB/s simultaneous copy speed to two targets
  • DoD certified erase sanitises drives securely
  • 128 MB DDR2 buffer handles large transfers
  • Compact tablet-sized frame fits in a bag

Compact two-target SATA duplicator

The VinPower HDDMINIDUP-2 is a standalone duplicator that copies one source drive to up to two SATA targets simultaneously. Its tablet-sized frame supports both 2.5 and 3.5 inch hard drives and solid-state drives without requiring a host computer. Menus appear in English, Spanish, French, German, Italian and Japanese on a 20 by 2 blue LCD panel.

Sustained 90 MB per second cloning speed

Actual transfer rate reaches 90 MB per second across both target ports at the same time, so large-capacity drives up to 3 TB and beyond finish in minutes rather than hours. The 128 MB DDR2 buffer absorbs burst traffic to keep throughput steady during long cloning or sanitisation jobs. Operation stays consistent because the unit runs independently of PC software or operating-system overhead.

Check your drives and optional CF needs

Verify that every drive you plan to use has a standard SATA connector compatible with 1.5, 3.0 or 6.0 Gbps signalling. CompactFlash media are not supported unless the separate CF interface module add-on is purchased. The duplicator handles only SATA devices; other interfaces or form factors cannot be connected.

Prednosti

  • Standalone operation needs no PC attached
  • 90 MB/s simultaneous copy speed to two targets
  • DoD certified erase sanitises drives securely
  • 128 MB DDR2 buffer handles large transfers
  • Compact tablet-sized frame fits in a bag

Špecifikácie

BrandVINPOWER
ModelHDDMINIDUP-2
TypeHard Drive Duplicator
Target1 to 2
Buffer Memory128MB DDR2
Language SupportEnglish, Spanish, French, German, Italian, Japanese, and more(Chinese and Arabic can be ordered on request)
Display20 x 2 Blue LCD
Operating TypeStandalone
ConnectorSATA I & II (1.5G & 3.0G), SATA III (6.0G) Compatible
Panel ColorBlack
FeaturesHardware:
Small lightweight compact frame (about the size of a small tablet) for easy travel
Optional CF Support with optional CF Interface Module Add-on
Support of all SATA Interface, 1.5Gbps, 3.0Gbps, 6.0Gbps
Industry Standard 90MB/s (5GB/min) Simultaneous Actual Transfer Speed
2.5" and 3.5" HDD/SSD Support
Supports HDD sizes 3TB +: The HDDMINI can accurately copy very high capacity HDD's, including 3TB and larger, for long term archival storage or large capacity data files.
Software:
Standalone Operation, No PC is required
Simultaneous and Independent HDD operation
DoD Certified H
Prepravná hmotnosť0.88 kg
Rozmery balenia216 × 160 × 71 mm

Otázky k tomuto produktu

How much heat or noise does the HDDMINIDUP-2 produce when running a full-day duplication job?

The duplicator uses a small lightweight frame about the size of a tablet with no active cooling mentioned, so it runs quietly and stays cool during extended 90 MB/s copy sessions.

What drives or cables must I already own to start cloning with this duplicator?

You need up to two SATA hard drives or SSDs in 2.5 or 3.5 inch form factors; the unit provides the SATA connectors and operates standalone without a PC.

Will the duplicator work reliably with older SATA I drives that only run at 1.5 Gbps?

Yes, the connector specification lists SATA I and II at 1.5 and 3.0 Gbps as compatible alongside SATA III 6.0 Gbps, so legacy drives clone at their native speed.

Aj v tomto oddelení

Zákazníci tiež porovnávali

Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.