BFKK
BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
214,99 US$
0.00278452BTC
I lager
G.SKILL
G.SKILL Ripjaws V 16GB (2x8GB) DDR4-2400 CL15 F4-2400C15D-16GVR desktop RAM
A 16 GB dual-channel DDR4 kit running at 2400 MT/s with CL15 latency and a red aluminum heatspreader
- Capacity16GB (2 x 8GB)
- Type288-Pin PC RAM
- SpeedDDR4 2400 (PC4 19200)
- CAS LatencyCL15
- Timing15-15-15-35
- Voltage1.20V
- Dual-channel 16 GB kit boosts multitasking headroom
- CL15 latency sharpens response in latency-sensitive workloads
- 20 V operation reduces power draw and heat
- Aluminium heatspreader keeps modules cool under load
- Intel XMP 2.0 profile enables one-click 2400 MT/s setup
Ripjaws V dual-channel kit
This G.SKILL Ripjaws V kit provides 16GB of DDR4 memory in a matched 2x8GB configuration. It targets desktop builders who want reliable dual-channel performance on supported Intel platforms. The modules run at DDR4 2400 with a CAS latency of 15 and timings of 15-15-15-35.
Aluminium heatspreader and 288-pin layout
Each stick carries a red aluminium heatspreader that helps manage thermals during sustained loads. The standard 288-pin DDR4 form factor fits mainstream desktop motherboards without special clearance requirements. Intel XMP 2.0 allows the rated speed and timings to be applied through a single BIOS selection.
DDR4 2400 bandwidth ceiling
The PC4 19200 rating sets a hard limit on maximum theoretical throughput regardless of tighter timings or higher voltages. Operating at 1.20V keeps power draw modest but also caps headroom for manual overclocking beyond the XMP profile. Mixing this kit with other modules is not supported and can prevent the system from booting at the rated specification.
I korthet
- Dual-channel 16 GB kit boosts multitasking headroom
- CL15 latency sharpens response in latency-sensitive workloads
- 20 V operation reduces power draw and heat
- Aluminium heatspreader keeps modules cool under load
- Intel XMP 2.0 profile enables one-click 2400 MT/s setup
Specifikationer
| Brand | G.SKILL |
|---|---|
| Series | Ripjaws V Series |
| Model | F4-2400C15D-16GVR |
| Capacity | 16GB (2 x 8GB) |
| Type | 288-Pin PC RAM |
| Speed | DDR4 2400 (PC4 19200) |
| CAS Latency | CL15 |
| Timing | 15-15-15-35 |
| Voltage | 1.20V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Multi-channel Kit | Dual Channel Kit |
| BIOS/Performance Profile | Intel XMP 2.0 |
| Color | Red |
| Heat Spreader | Yes |
| Features | Overclock performance DDR4 memory designed for compatible Intel platforms. Sleek and stylish aluminum heatspreader design. Intel XMP 2.0 support. Do not mix memory kits. Memory kits are sold in matched kits that are designed to run together as a set. Mixing memory kits will result in stability issues or system failure. Memory kits will boot at the SPD speed at default BIOS settings with compatible hardware. For memory kits with XMP, enable XMP/DOCP/A-XMP in BIOS to reach the rated potential XMP overclock speed of the memory kit, subject to the use of compatible hardware. Reaching the |
| Recommend Use | AMD X570 / B550 Intel X99 / X299 / Z690 DDR4 / Z590 / Z490 / Z390 / Z370 / Z270 / Z170 |
Frågor om den här produkten
What does the DDR4-2400 PC4-19200 rating mean for real-world bandwidth?
The kit runs at 2400 MT/s with a PC4-19200 peak transfer rate, so dual-channel throughput is capped at the JEDEC DDR4-2400 limit unless the motherboard enables a higher XMP profile.
Will the 288-pin modules with the aluminum heatspreader clear my CPU cooler?
Each stick is a standard 288-pin DIMM with a low-profile Ripjaws V heatspreader; most tower coolers leave enough clearance, but measure from the motherboard to the cooler base before ordering.
How do I enable the rated CL15 15-15-15-35 timings at 1.20 V on my board?
Enter the BIOS, turn on Intel XMP 2.0 for the kit, save and reboot; the common mistake is leaving XMP off so the modules fall back to slower JEDEC defaults.
Även i den här avdelningen
Andra har jämfört dessa
Samma hylla, samma kassa — åtta mynt och ett 30-minuters kurslås.
