Vi tar emot kryptovaluta — så att kryptot du äger kan köpa riktig hårdvara.Betala med krypto, använd det till riktig hårdvara. Fri, försäkrad frakt över hela världen vid köp över 399 $. Neutrala, omärkta ytterkartonger, skickade från Tyskland.Fri, försäkrad frakt över 399 $. Din kurs låses i 30 minuter så snart kassan öppnas.Kursen låst i 30 minuter. Varje artikel är förseglad, har kontrollerat serienummer och täcks av 24 månaders garanti.Förseglad, 24 månaders garanti.

Bevakade produkter Logga in

LORDWORLD

LORDWORLD ESP32-C6 Development Board ESP32-C6-WROOM-1-N8 8MB Flash

SKU CH-YPBD-MFYF3

IoT development board with RISC-V 32-bit processor at 160MHz, 8MB flash, WiFi 6, Bluetooth 5 and IEEE 802.15.4, USB-UART via CH343 and CH334, castellated module for carrier boards

  • RISC-V 32-bit single-core processor up to 160MHz for efficient edge computing
  • 8MB Flash built into ESP32-C6-WROOM-1-N8 module stores firmware and data
  • WiFi 6 plus Bluetooth 5 and IEEE 802.15.4 for multi-protocol IoT connectivity
  • USB Type-C with CH343 and CH334 chips enables USB and UART development
  • Pin-compatible with ESP32-C6-DevKitC-1-N8 and castellated for carrier-board soldering

ESP32-C6 RISC-V development board

This LORDWORLD board integrates the ESP32-C6-WROOM-1-N8 module with a 32-bit single-core RISC-V processor running up to 160MHz and 8MB flash storage. It targets makers and engineers building IoT edge devices that need WiFi 6, Bluetooth 5, and IEEE 802.15.4 connectivity in a compact form factor. The castellated module design also allows direct soldering onto custom carrier boards for production deployments.

Low-power wireless operation

The ESP32-C6 chip is designed for energy-efficient IoT applications with its RISC-V core and integrated radio subsystems. WiFi 6, Bluetooth 5, and IEEE 802.15.4 (supporting Zigbee 3.0 and Thread) share the same silicon, enabling multi-protocol connectivity without additional power-hungry components. The onboard CH343 and CH334 chips handle USB-to-UART conversion through the Type-C connector for development and debugging.

Pin-compatible expandability

The board matches the ESP32-C6-DevKitC-1-N8 pinout, letting you reuse existing shield designs and peripheral layouts. Onboard CH343 and CH334 chips provide USB and UART interfaces over a single Type-C port, simplifying firmware flashing and serial monitoring. Castellated edges on the module enable direct surface-mount assembly onto custom PCBs when moving from prototype to production.

I korthet

  • RISC-V 32-bit single-core processor up to 160MHz for efficient edge computing
  • 8MB Flash built into ESP32-C6-WROOM-1-N8 module stores firmware and data
  • WiFi 6 plus Bluetooth 5 and IEEE 802.15.4 for multi-protocol IoT connectivity
  • USB Type-C with CH343 and CH334 chips enables USB and UART development
  • Pin-compatible with ESP32-C6-DevKitC-1-N8 and castellated for carrier-board soldering

Specifikationer

BrandLORDWORLD

Frågor om den här produkten

How do I install the board and what step do people often miss?

Connect the Type-C cable to install drivers for the onboard CH343 and CH334 chips, then select the correct COM port in your IDE; the step often missed is putting the ESP32-C6-WROOM-1-N8 module into boot mode by holding the BOOT button while pressing RESET before uploading code.

What maintenance or replacement will this development board need later?

The board has no user-replaceable parts; long-term care is limited to keeping the Type-C connector and castellated module pads free of dust and corrosion, and re-flashing the 8MB Flash if firmware becomes corrupted.

What limit appears first when the board runs continuously at 160MHz with WiFi 6 and Bluetooth 5 active?

The on-module RF front-end and voltage regulator reach thermal saturation first, causing the ESP32-C6-WROOM-1-N8 to throttle its RISC-V 32-bit single-core processor below 160MHz to protect the 8MB Flash and wireless circuitry.

Även i den här avdelningen

Andra har jämfört dessa

Samma hylla, samma kassa — åtta mynt och ett 30-minuters kurslås.