EN-Labs 11-001-366 PCIe x4 USB 3.2 10Gbps 5-port card
- no
- 12CM Case fan,screw…
نقبل الدفع بالعملة المشفرة — لذلك يمكن للعملات الرقمية التي تملكها أن تشتري أجهزة حقيقية.ادفع بالعملة المشفرة، وأنفقها على أجهزة حقيقية. شحن مؤمن مجانا إلى كل أنحاء العالم لما يتجاوز 399 US$. صناديق شحن بسيطة بلا علامة تجارية، ترسل من ألمانيا.شحن مؤمن مجانا لما يتجاوز 399 US$. يُقفل سعرك لمدة 30 دقيقة بمجرد فتح صفحة الدفع.السعر مقفل لمدة 30 دقيقة. كل قطعة مختومة، ورقمها التسلسلي متحقق منه، ومشمولة بضمان 24 شهرا.مختوم، وبضمان 24 شهرا.
myVolts
ATX power supply delivering 500 W with manual 115/230 V switching, thermal fan control and 1.1 m cord
This myVolts ATX-500W unit delivers 500 W of rated power for basic desktop systems that prioritise low energy consumption and quiet operation. Clear connector markings simplify installation for first-time builders or office refreshes. A 1.1 m mains cable reaches most wall sockets without an extension lead. Efficiency exceeds 80 percent under typical loads.
The power supply uses a manual voltage selector rather than active PFC, so the user must set the switch to match the local mains before connecting. Hold-up time is greater than 10 ms, providing a brief buffer during short power interruptions. Thermal sensing adjusts the 12 cm fan speed automatically to balance airflow and noise. Rated service life is 100000 hours at normal operating temperatures.
Four SATA power connectors support multiple hard drives or SSDs in a storage-focused build. The single 6-pin to 6+2-pin PCIe cable limits graphics-card options to models drawing no more than 150 W from the connector. Motherboard power uses a 20+4-pin ATX plug alongside a 4+4-pin 12 V CPU header. Two additional fan headers are available for case cooling.
| Type | AT |
|---|
This unit is offered as a single 500W model, rated for low-energy systems with an efficiency above 80% and a 100000-hour service life.
It provides 500W continuous power with a hold-up time greater than 10ms, supporting a 20+4 pin motherboard connector, dual 4-pin CPU power, four SATA drives and a 6-pin to 6+2-pin GPU cable.
You set the input voltage switch to match your mains supply; the unit has no active PFC, so the switch must be correct before powering on.
أيضًا في هذا القسم
نفس القسم، ونفس صفحة الدفع — ثماني عملات رقمية وقفل سعر لمدة 30 دقيقة.
ما تدفعه، وما تُعرض به الأسعار.
يُرسَل من محفظتك عند إتمام الطلب
للعرض فقط — أسعار الكتالوج بالدولار الأمريكي
لا توجد عملة مطابقة.
اختر اللغة التي يخاطبك بها الموقع.
هل أنت جديد هنا؟
لديك حساب بالفعل؟
لا توجد إعادة تعيين تلقائية: هذا المتجر لا يُرسل أي بريد، فلا يوجد رابط لمرة واحدة يمكن طلبه. اترك العنوان في الحساب، وسيُعالَج الأمر يدويًا.
تم تسجيل الطلب
لا شيء في طريقه إلى بريدك الوارد — هذا المتجر لا يُرسل أي بريد إطلاقًا. يتولّى أحدهم معالجة هذه الطلبات يدويًا.
تذكّرتها؟