NEMIX RAM DDR5-5600 2TB (16x128GB) ECC RDIMM CL46 1.1V Supermicro H14SST-G memory upgrade
- 2TB (16 x 128GB)
- 288-Pin DDR5 RDIMM
نقبل الدفع بالعملة المشفرة — لذلك يمكن للعملات الرقمية التي تملكها أن تشتري أجهزة حقيقية.ادفع بالعملة المشفرة، وأنفقها على أجهزة حقيقية. شحن مؤمن مجانا إلى كل أنحاء العالم لما يتجاوز 399 US$. صناديق شحن بسيطة بلا علامة تجارية، ترسل من ألمانيا.شحن مؤمن مجانا لما يتجاوز 399 US$. يُقفل سعرك لمدة 30 دقيقة بمجرد فتح صفحة الدفع.السعر مقفل لمدة 30 دقيقة. كل قطعة مختومة، ورقمها التسلسلي متحقق منه، ومشمولة بضمان 24 شهرا.مختوم، وبضمان 24 شهرا.
OWC
8GB DDR3 1333 ECC registered server memory module with CL9 latency and 1.5V operation
This 8 GB DDR3 module is built for workstations and servers that require ECC registered memory. It operates at 1333 MHz with CL9 latency and a 1.5 V supply. The 2Rx4 dual-rank organisation suits multi-slot configurations where registered buffering is mandatory.
The standard 240-pin RDIMM layout fits server mainboards designed for registered ECC DDR3. No heat spreader is fitted, so airflow across the PCB is unimpeded in dense chassis. JEDEC and RoHS compliance confirms the module meets baseline electrical and environmental specs for warranty-safe upgrades.
Check that your platform explicitly accepts DDR3 registered ECC RDIMMs; standard desktop boards will not post with this module. Do not mix registered and unbuffered DIMMs in the same system. Confirm the memory controller can address 2Rx4 modules at the required speed before ordering.
| Brand | OWC |
|---|---|
| Part Number | 1R3D32R408GB |
| Capacity | 8GB |
| Type | 240-Pin DDR3 ECC RDIMM |
| Speed | DDR3 1333 (PC3 10600) |
| CAS Latency | CL9 |
| Voltage | 1.5V |
| ECC | Yes |
| Buffered/Registered | Registered |
| Rank | 2Rx4 |
| Heat Spreader | No |
The module runs at 1333 MT/s with a peak bandwidth of PC3-10600 and a CAS latency of 9 cycles, so sustained throughput is capped by the DDR3-1333 JEDEC ceiling.
It needs a standard 240-pin DDR3 DIMM socket; the registered 2Rx4 design adds a register chip but keeps the same height as a plain DDR3 module, so no extra clearance is needed.
Power down, open the chassis, align the notch on the 240-pin edge connector, press firmly until both latches click, then verify in BIOS that ECC and registered mode are enabled — skipping the BIOS check is the step most people forget.
أيضًا في هذا القسم
نفس القسم، ونفس صفحة الدفع — ثماني عملات رقمية وقفل سعر لمدة 30 دقيقة.
ما تدفعه، وما تُعرض به الأسعار.
يُرسَل من محفظتك عند إتمام الطلب
للعرض فقط — أسعار الكتالوج بالدولار الأمريكي
لا توجد عملة مطابقة.
اختر اللغة التي يخاطبك بها الموقع.
هل أنت جديد هنا؟
لديك حساب بالفعل؟
لا توجد إعادة تعيين تلقائية: هذا المتجر لا يُرسل أي بريد، فلا يوجد رابط لمرة واحدة يمكن طلبه. اترك العنوان في الحساب، وسيُعالَج الأمر يدويًا.
تم تسجيل الطلب
لا شيء في طريقه إلى بريدك الوارد — هذا المتجر لا يُرسل أي بريد إطلاقًا. يتولّى أحدهم معالجة هذه الطلبات يدويًا.
تذكّرتها؟