HP 507283-001 146GB 10000 RPM SAS 2.5" internal hard drive
- Bare Drive
- SATA
نقبل الدفع بالعملة المشفرة — لذلك يمكن للعملات الرقمية التي تملكها أن تشتري أجهزة حقيقية.ادفع بالعملة المشفرة، وأنفقها على أجهزة حقيقية. شحن مؤمن مجانا إلى كل أنحاء العالم لما يتجاوز 399 US$. صناديق شحن بسيطة بلا علامة تجارية، ترسل من ألمانيا.شحن مؤمن مجانا لما يتجاوز 399 US$. يُقفل سعرك لمدة 30 دقيقة بمجرد فتح صفحة الدفع.السعر مقفل لمدة 30 دقيقة. كل قطعة مختومة، ورقمها التسلسلي متحقق منه، ومشمولة بضمان 24 شهرا.مختوم، وبضمان 24 شهرا.
SAMSUNG
A 1.92 TB SATA 2.5" internal SSD delivering up to 520 MBps read and 485 MBps write speeds with 97000 IOPS random read and 29000 IOPS random write
The Samsung SM863a is a 1.92TB internal solid-state drive built on QLC flash with a 2.5-inch SATA 6Gbps interface. It delivers up to 520 MBps sequential read and 485 MBps sequential write speeds. Random performance reaches 97000 IOPS read and 29000 IOPS write. The drive draws 3.45W active power and carries a 2,000,000-hour MTBF rating.
This drive fits read-intensive server roles, media libraries and backup targets where capacity per pound matters and write cycles stay moderate. Heavy transactional databases, high-endurance logging or sustained high-write workloads should look at drives with higher write endurance ratings.
Confirm your chassis has a free 2.5-inch drive bay or a 3.5-inch adapter bracket. Ensure the motherboard or controller provides a SATA 6Gbps port and that your power supply includes a spare SATA power connector. Check BIOS or RAID controller firmware for SSD trim support.
| Brand | SAMSUNG |
|---|---|
| Part Number | MZ-7KM1T9N |
| Device Type | Internal Solid State Drive (SSD) |
| Form Factor | 2.5" |
| Capacity | 1.92TB |
| Max Sequential Read | Up to 520 MBps |
| Max Sequential Write | Up to 485 MBps |
| 4KB Random Read | Up to 97000 Iops |
| 4KB Random Write | Up to 29000 Iops |
| MTBF | 2,000,000 hours |
| Power Consumption (Active) | 3.45W |
Yes, the drive uses a standard 2.5" form factor and SATA interface, so an available 2.5" drive bay and a SATA power connector from your PSU are required for installation.
The drive supports SATA 6Gbps but is backward compatible with 3Gbps ports; on an older controller the sequential read will be limited to the 3Gbps link speed rather than the rated 520 MBps.
Run a 4KB random read benchmark such as CrystalDiskMark or AS SSD and compare the reported IOPS to the 97000 IOPS specification to verify the drive is operating as intended.
أيضًا في هذا القسم
نفس القسم، ونفس صفحة الدفع — ثماني عملات رقمية وقفل سعر لمدة 30 دقيقة.
ما تدفعه، وما تُعرض به الأسعار.
يُرسَل من محفظتك عند إتمام الطلب
للعرض فقط — أسعار الكتالوج بالدولار الأمريكي
لا توجد عملة مطابقة.
اختر اللغة التي يخاطبك بها الموقع.
هل أنت جديد هنا؟
لديك حساب بالفعل؟
لا توجد إعادة تعيين تلقائية: هذا المتجر لا يُرسل أي بريد، فلا يوجد رابط لمرة واحدة يمكن طلبه. اترك العنوان في الحساب، وسيُعالَج الأمر يدويًا.
تم تسجيل الطلب
لا شيء في طريقه إلى بريدك الوارد — هذا المتجر لا يُرسل أي بريد إطلاقًا. يتولّى أحدهم معالجة هذه الطلبات يدويًا.
تذكّرتها؟