Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Green rectangular DDR4 DIMM with black chips and gold contacts

A-Tech

A-Tech 16GB DDR4 2933 ECC RDIMM 2Rx8 CL21 server RAM

SKU CH-2PMY-BR0JG

16 GB DDR4 2933 ECC registered server memory with CL21 latency and 2Rx8 organisation

  • Capacity16GB
  • SpeedDDR4 2933 (PC4 23400)
  • CAS LatencyCL21
  • Voltage1.20V
  • ECCYes
  • Buffered/RegisteredRegistered
  • 16GB ECC RDIMM protects server data integrity with error correction
  • 2933MHz DDR4 speed handles heavy workloads through high bandwidth
  • CL21 latency keeps response times tight for multi-thread tasks
  • 20V operation reduces power draw and heat in dense racks
  • 2Rx8 dual-rank layout increases memory density per 288-pin slot

16GB DDR4 2933 ECC RDIMM for servers

This 16GB DDR4 2933 ECC RDIMM uses a 2Rx8 registered design and runs at 1.20V with CL21 latency. It is built for server and workstation platforms that require registered DIMMs with error-correcting code. The module is a direct replacement for several Kingston part numbers including KTD-PE429D8/16G and KSM29RD8/16HDR.

Sustained workload behaviour

Registered buffering and ECC circuitry keep data integrity intact during continuous multi-threaded workloads. The 2Rx8 organisation allows the memory controller to interleave accesses across two ranks, helping maintain throughput when all slots are populated. CL21 timing at 2933 MT/s delivers consistent latency without the variability seen in unbuffered consumer modules.

Installation notes and common issues

The 288-pin DIMM fits standard DDR4 RDIMM slots; alignment is keyed so it cannot be inserted backwards. Systems that only accept unbuffered UDIMMs or that limit rank count per channel will not recognise this module. Always confirm the platform supports registered ECC memory and the maximum rank population per channel before ordering. Buyers needing unbuffered memory or higher speeds than 2933 MT/s should look elsewhere.

Přednosti

  • 16GB ECC RDIMM protects server data integrity with error correction
  • 2933MHz DDR4 speed handles heavy workloads through high bandwidth
  • CL21 latency keeps response times tight for multi-thread tasks
  • 20V operation reduces power draw and heat in dense racks
  • 2Rx8 dual-rank layout increases memory density per 288-pin slot

Specifikace

BrandA-Tech
Capacity16GB
SpeedDDR4 2933 (PC4 23400)
CAS LatencyCL21
Voltage1.20V
ECCYes
Buffered/RegisteredRegistered
Rank2Rx8
ChipsetMajor Brand Chipset
FeaturesMajor Brand Chips

Otázky k tomuto produktu

How much power does this 16 GB DDR4 2933 ECC RDIMM draw at its rated 1.20 V?

The module operates at the standard DDR4 voltage of 1.20 V, so typical power draw stays within the JEDEC limit for a 16 GB registered DIMM at 2933 MT/s.

Does my motherboard need to support registered ECC DDR4 and 288-pin DIMM slots for this stick to work?

Yes — the module is a 288-pin DDR4 RDIMM with ECC and registered buffering, so the platform must accept registered ECC memory in a standard DDR4 DIMM slot.

Can I mix this 2Rx8 CL21 module with older single-rank DDR4 RDIMMs in the same server?

Mixing ranks is often supported, but the system will run all modules at the speed and timings of the slowest stick; check your server's memory population rules before combining.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.