Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Grey PLA filament on a white spool, 1.75 mm diameter, neatly wound

BFKK

BFKK PLA Filament 1.75mm Grey 1kg Spool +/-0.02mm

SKU CH-JCY4-R63CA

Grey PLA filament on a 1 kg spool with ±0.02 mm accuracy for reliable FDM printing

  • Colorgrey

Color grey

  • PLA prints reliably with no clogs, bubbles or tangles
  • Neat winding at 100 % rate prevents jams and ensures smooth feeding
  • Dimensional accuracy ±0.02 mm fits almost every 1.75 mm FDM printer
  • Spool dimensions 8.00" × 2.50" × 2.20" hub suit most printer holders
  • Recommended settings 200–230 °C nozzle, 50–65 °C bed, 50–100 mm/s speed

Grey PLA Filament 1.75 mm

This grey PLA filament comes on a 1 kg spool with a 1.75 mm diameter and a dimensional accuracy of +/- 0.02 mm. It is designed for FDM 3D printers and suits both beginners and experienced users. The material prints reliably with good layer adhesion and minimal risk of clogs or bubbles.

Upgrade from inconsistent or tangled filament

Switching to this spool is worthwhile when your current filament suffers from diameter variation, frequent tangles, or poor layer bonding. The tight 0.02 mm tolerance and neat winding reduce jams and improve print consistency. It replaces low-quality PLA that causes failed prints or requires constant monitoring.

Easy loading with standard spool dimensions

The spool measures 8.00 inches in diameter, 2.50 inches wide, and has a 2.20 inch hub hole, fitting most FDM printer holders. Filament feeds smoothly thanks to the 100 % neat winding process. Print at 200-230 °C nozzle temperature, 50-65 °C bed temperature, and 50-100 mm/s speed for best results.

Přednosti

  • PLA prints reliably with no clogs, bubbles or tangles
  • Neat winding at 100 % rate prevents jams and ensures smooth feeding
  • Dimensional accuracy ±0.02 mm fits almost every 1.75 mm FDM printer
  • Spool dimensions 8.00" × 2.50" × 2.20" hub suit most printer holders
  • Recommended settings 200–230 °C nozzle, 50–65 °C bed, 50–100 mm/s speed

Specifikace

Colorgrey

Další verze tohoto modelu

Dalších 5 v této řadě

Stejná řada, jiná paměť, chladič nebo takt — porovnejte, než se rozhodnete.

Otázky k tomuto produktu

Will the 8.00 inch diameter spool with a 2.20 inch hub hole fit my printer's filament holder?

The spool measures 8.00 inches in diameter, 2.50 inches wide, and has a 2.20 inch centre hole, so it fits most standard FDM printer mounts.

What nozzle and bed temperatures should I set for the first layer to avoid adhesion problems?

Start at 200 to 230 °C nozzle temperature and 50 to 65 °C bed temperature; many users forget to raise the bed into the 50 to 65 °C range for the first layer.

How often should I dry this PLA if it absorbs moisture after opening?

Dry the filament at low heat for a few hours whenever prints show stringing or popping; the 1.75 mm diameter with .02 mm tolerance stays consistent after proper drying.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.