Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Two green circuit boards with black memory chips, no heat spreaders, 288-pin DDR4 DIMM form factor

Computer Memory Solutions

Computer Memory Solutions 16GB (2x8GB) DDR4 2666 CL19 DIMM for OptiPlex 7060/XE3

SKU CH-TPAK-W6FTB

A 16 GB DDR4 kit of two 8 GB unbuffered DIMMs at 2666 MHz CL19 for Dell OptiPlex 7060 and XE3 systems

  • Capacity16GB (2 x 8GB)
  • Type288-Pin DDR4 SDRAM
  • SpeedDDR4 2666 (PC4 21300)
  • CAS LatencyCL19
  • Timing19-19-19
  • Voltage1.20V
  • 16 GB dual-channel kit boosts multitasking headroom
  • 2666 MHz DDR4 speed matches OptiPlex 7060 spec
  • CL19 latency keeps response tight at 1.2 V
  • Guaranteed fit for OptiPlex 7060 SFF, Tower and XE3 Tower
  • Two 8 GB unbuffered DIMMs install in seconds

16 GB DDR4 kit for OptiPlex 7060 and XE3

This 16 GB kit uses two 8 GB DDR4 DIMMs rated at 2666 MHz with CL19 timing. It targets owners of Dell OptiPlex 7060 SFF, OptiPlex 7060 Tower or OptiPlex XE3 Tower systems who need more memory for everyday workloads. The modules are unbuffered, non-ECC and run at 1.2 V.

No heat spreaders and major-brand chips

The sticks ship without heat spreaders, keeping the profile low for small-form-factor chassis. Major-brand chipsets are used to reduce compatibility issues. All installed memory will operate at the speed of the slowest module or the processor limit, so mixing with slower RAM reduces overall throughput.

Simple 288-pin DIMM installation

Installation follows the standard 288-pin DDR4 DIMM procedure for the four available slots. Buyers who need more than 64 GB total capacity or who require ECC or registered memory cannot use this kit. Ensure the system firmware is current to avoid recognition problems with 2Rx8 rank modules.

Přednosti

  • 16 GB dual-channel kit boosts multitasking headroom
  • 2666 MHz DDR4 speed matches OptiPlex 7060 spec
  • CL19 latency keeps response tight at 1.2 V
  • Guaranteed fit for OptiPlex 7060 SFF, Tower and XE3 Tower
  • Two 8 GB unbuffered DIMMs install in seconds

Specifikace

BrandComputer Memory Solutions
ModelCM1024642666DIMM
Capacity16GB (2 x 8GB)
Type288-Pin DDR4 SDRAM
SpeedDDR4 2666 (PC4 21300)
CAS LatencyCL19
Timing19-19-19
Voltage1.20V
ECCNo
Buffered/RegisteredUnbuffered
Rank2Rx8
ChipsetMajor Brand Chipset
Heat SpreaderNo
Compatible SystemDell OptiPlex 7060 Small Form Factor (SFF), OptiPlex 7060Tower, OptiPlex XE3 Tower
Package Content2 Memory RAM Sticks

Otázky k tomuto produktu

Will the 288-pin DDR4 modules need replacement if I later expand to the 64 GB maximum?

The kit occupies two of the four slots with 8 GB sticks, so you can add two more modules later without removing these.

What speed ceiling will the memory hit first during long workloads?

All installed modules run at the slowest speed present, so the 2666 MHz CL19 rating sets the limit for the whole system.

How much heat and power will the 1.2 V unbuffered DIMMs produce running all day?

At 1.2 V with no heat spreader, each 8 GB stick draws minimal power and stays cool under continuous load.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.