Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Bare 3.5 inch SAS hard drive, silver metal casing, circuit board visible on underside

DELL

DELL 400-ANWD 10TB 3.5" SAS 7200 RPM internal hard drive

SKU CH-5JDH-77VS0

A 10 TB 3.5" SAS internal hard drive spinning at 7200 RPM with a 12 Gb/s interface and hot-swap capability for Dell PowerEdge servers

  • PackagingBare Drive
  • InterfaceSAS 12Gb/s
  • Capacity10TB
  • RPM7200 RPM
  • Average Latency12Gb/s
  • Form Factor3.5"
  • 10 TB capacity expands server storage
  • SAS 12 Gb/s interface enables fast data transfer
  • 7200 RPM spindle speed provides quick disk access
  • Hot-plug design allows drive replacement without downtime
  • Compatible with Dell PowerEdge R230 R330 R430 R530 R730 R730XD T330 T430 T630

10 TB SAS Hard Drive for PowerEdge Servers

The Dell 400-ANWD is a 10 TB internal hard drive built for Dell PowerEdge servers. It uses a 12 Gb/s SAS interface and spins at 7200 RPM to deliver fast disk access. The 3.5 inch form factor supports hot-plug installation in compatible bays. This new drive suits administrators expanding storage on supported Dell systems.

Replaces Smaller SAS Drives in Hot-Plug Bays

This drive upgrades from lower-capacity SAS drives when more space is needed in the same hot-plug slot. The jump is worth it when workloads demand 10 TB of near-line storage with 12 Gb/s throughput. It fits the same 3.5 inch carrier used by earlier Dell SAS drives. Buyers needing a different interface or a non-hot-plug drive should look elsewhere.

Check Server Model and Controller Compatibility

Verify that your PowerEdge server appears in the supported list before ordering. The drive requires a SAS controller or backplane that operates at 12 Gb/s. Confirm the chassis accepts 3.5 inch hot-plug trays and that the firmware supports 4Kn sector formatting. Unsupported servers or controllers will not recognise the drive.

Přednosti

  • 10 TB capacity expands server storage
  • SAS 12 Gb/s interface enables fast data transfer
  • 7200 RPM spindle speed provides quick disk access
  • Hot-plug design allows drive replacement without downtime
  • Compatible with Dell PowerEdge R230 R330 R430 R530 R730 R730XD T330 T430 T630

Specifikace

BrandDell
Model400-ANWD
PackagingBare Drive
InterfaceSAS 12Gb/s
Capacity10TB
RPM7200 RPM
Average Latency12Gb/s
Form Factor3.5"

Otázky k tomuto produktu

What drive bay size does the 3.5" 10TB SAS hard drive require?

The drive fits a standard 3.5-inch internal bay in compatible Dell PowerEdge servers such as the R230, R330, R430, R530, R730, R730XD, T330, T430 and T630.

How is the hot-plug 10TB SAS drive installed, and what step is often missed?

Slide the bare drive into a hot-swap carrier until the SAS connector seats firmly, then lock the carrier latch; the step often missed is fully engaging the latch so the drive registers on the 12Gb/s bus.

What component of the 7200 RPM SAS drive typically needs replacement after long-term use?

The mechanical spindle and actuator assembly inside the 10TB SAS drive will eventually wear, requiring full drive replacement when SMART data reports reallocated sectors or seek errors.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.