Nous acceptons la cryptomonnaie — les cryptos que vous détenez peuvent ainsi acheter du matériel réel.Payez en crypto, dépensez-la en matériel réel. Livraison assurée offerte partout dans le monde au-delà de 399 $. Cartons neutres, sans marque, expédiés depuis l’Allemagne.Livraison assurée offerte au-delà de 399 $. Votre taux est bloqué pendant 30 minutes dès l’ouverture de la caisse.Taux bloqué 30 minutes. Chaque article est scellé, son numéro de série est vérifié, et il est couvert par une garantie de 24 mois.Scellé, garanti 24 mois.

Articles suivis Se connecter
Bare 3.5 inch SAS hard drive, silver metal casing, circuit board visible on underside

DELL

DELL 400-ANWD 10TB 3.5" SAS 7200 RPM internal hard drive

SKU CH-5JDH-77VS0

A 10 TB 3.5" SAS internal hard drive spinning at 7200 RPM with a 12 Gb/s interface and hot-swap capability for Dell PowerEdge servers

  • PackagingBare Drive
  • InterfaceSAS 12Gb/s
  • Capacity10TB
  • RPM7200 RPM
  • Average Latency12Gb/s
  • Form Factor3.5"
  • 10 TB capacity expands server storage
  • SAS 12 Gb/s interface enables fast data transfer
  • 7200 RPM spindle speed provides quick disk access
  • Hot-plug design allows drive replacement without downtime
  • Compatible with Dell PowerEdge R230 R330 R430 R530 R730 R730XD T330 T430 T630

10 TB SAS Hard Drive for PowerEdge Servers

The Dell 400-ANWD is a 10 TB internal hard drive built for Dell PowerEdge servers. It uses a 12 Gb/s SAS interface and spins at 7200 RPM to deliver fast disk access. The 3.5 inch form factor supports hot-plug installation in compatible bays. This new drive suits administrators expanding storage on supported Dell systems.

Replaces Smaller SAS Drives in Hot-Plug Bays

This drive upgrades from lower-capacity SAS drives when more space is needed in the same hot-plug slot. The jump is worth it when workloads demand 10 TB of near-line storage with 12 Gb/s throughput. It fits the same 3.5 inch carrier used by earlier Dell SAS drives. Buyers needing a different interface or a non-hot-plug drive should look elsewhere.

Check Server Model and Controller Compatibility

Verify that your PowerEdge server appears in the supported list before ordering. The drive requires a SAS controller or backplane that operates at 12 Gb/s. Confirm the chassis accepts 3.5 inch hot-plug trays and that the firmware supports 4Kn sector formatting. Unsupported servers or controllers will not recognise the drive.

Points forts

  • 10 TB capacity expands server storage
  • SAS 12 Gb/s interface enables fast data transfer
  • 7200 RPM spindle speed provides quick disk access
  • Hot-plug design allows drive replacement without downtime
  • Compatible with Dell PowerEdge R230 R330 R430 R530 R730 R730XD T330 T430 T630

Caractéristiques

BrandDell
Model400-ANWD
PackagingBare Drive
InterfaceSAS 12Gb/s
Capacity10TB
RPM7200 RPM
Average Latency12Gb/s
Form Factor3.5"

Questions sur cet article

What drive bay size does the 3.5" 10TB SAS hard drive require?

The drive fits a standard 3.5-inch internal bay in compatible Dell PowerEdge servers such as the R230, R330, R430, R530, R730, R730XD, T330, T430 and T630.

How is the hot-plug 10TB SAS drive installed, and what step is often missed?

Slide the bare drive into a hot-swap carrier until the SAS connector seats firmly, then lock the carrier latch; the step often missed is fully engaging the latch so the drive registers on the 12Gb/s bus.

What component of the 7200 RPM SAS drive typically needs replacement after long-term use?

The mechanical spindle and actuator assembly inside the 10TB SAS drive will eventually wear, requiring full drive replacement when SMART data reports reallocated sectors or seek errors.

Également dans ce rayon

Les clients ont aussi comparé

Même rayon, même caisse — huit monnaies et un taux bloqué 30 minutes.