Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Small green circuit board with 40-pin and 44-pin IDE connectors, SATA port, and 23cm cable

EN-Labs

EN-Labs IDE2SATA 2.5" 3.5" IDE HDD to SATA Adapter with 23cm Cable

SKU CH-K56Q-KMBB8

Connects 2.5" or 3.5" IDE hard drives to SATA motherboards using the included 23cm cable

  • Connect legacy IDE drives to modern SATA systems
  • Supports 2.5" laptop 44pin IDE hard drives
  • Supports 3.5" desktop 40pin IDE hard drives
  • Includes 23cm SATA 22pin data and power combo cable
  • Powers 3.5" drives via 8cm Molex 4pin connection

IDE to SATA bridge for legacy drives

This adapter converts 2.5-inch and 3.5-inch IDE hard drives to a SATA interface. It supports both 44-pin laptop drives and 40-pin desktop drives, letting you connect older PATA storage to modern motherboards. The board includes a 23cm SATA 22-pin data and power extension cable for flexible installation.

Dual pin-header compatibility

The converter handles 44-pin 2.5-inch drives and 40-pin 3.5-inch drives on a single circuit board. Desktop 3.5-inch drives receive power through an 8cm Molex 4-pin connector on the adapter. No jumper configuration is required for the translation.

Passive operation with external power

The adapter draws no active cooling and adds negligible load to the system. The 3.5-inch drive is powered separately via the Molex connector, so the SATA port only carries data and 2.5-inch drive power. Cable length is limited to the included 23cm extension.

Přednosti

  • Connect legacy IDE drives to modern SATA systems
  • Supports 2.5" laptop 44pin IDE hard drives
  • Supports 3.5" desktop 40pin IDE hard drives
  • Includes 23cm SATA 22pin data and power combo cable
  • Powers 3.5" drives via 8cm Molex 4pin connection

Specifikace

Pro tento produkt zatím nejsou zveřejněny žádné specifikace.

Otázky k tomuto produktu

Will this adapter let me run a 44-pin laptop IDE drive at full SATA speed?

The adapter converts the 44-pin laptop IDE interface to SATA, so the drive runs at its native PATA rate; the SATA link itself does not increase the drive's original throughput.

Does the 40-pin desktop IDE connection require a separate Molex power lead?

Yes, the 40-pin desktop IDE drive is powered through an 8 cm Molex 4-pin connector that you must supply from your power supply.

What clearance do I need for the 23 cm SATA 22-pin combo cable inside my case?

The included 23 cm SATA 22-pin data-and-power cable needs enough room for its combined connector and the adapter board to sit behind a 2.5" or 3.5" drive bay.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.