Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Green rectangular circuit board with blue potentiometer and silver screw terminals

JacobsParts Inc.

JacobsParts Inc. XL6019 30W 5A DC-DC Boost Power Regulator power supply

SKU CH-22RJ-X7RYC

A step-up voltage regulator that converts 3–40 V DC input to a stable 5–45 V output at up to 5 A peak current with overcurrent, reverse-current and thermal protection

  • TypeStep-Up Voltage Regulator
  • Mounting StyleStand Alone
  • Current Rating5 A
  • Power Rating30 W
  • FeaturesOvercurrent Protection, Reverse Current Protection, Thermal
  • Boosts voltage from 3.7 V lithium cells to stable 5 V USB power
  • Delivers up to 5 A peak current for demanding automotive projects
  • Integrated XL6019 IC provides over-temperature and over-current protection
  • Operates at 180 kHz switching frequency with up to 94 % efficiency
  • Adjustable 5 V to 45 V output from 3 V to 40 V input range

DC-DC Boost Regulator for DIY Projects

This step-up module raises a lower DC input to a higher regulated output for hobbyist and prototype work. It accepts 3 V to 40 V in and delivers 5 V to 45 V out at up to 5 A peak. The XL6019 IC integrates a MOSFET with over-current and over-temperature protection. Screw terminals simplify wiring on the bench or in a vehicle.

Input Must Stay Below Output Voltage

Because the topology is boost-only, the supply voltage must always be lower than the desired output; the regulator cannot buck or pass-through. The adjustable potentiometer may need up to 15 turns before the output begins to move. Maximum recommended power is 30 W and efficiency reaches 94 % depending on the voltage differential. Output ripple stays below 100 mV at 180 kHz switching.

5 A Peak Current Defines the Load Limit

Sustained current is rated at 3 A with a 5 A peak allowance, so the module suits LED strips, USB charging from a 3.7 V cell, or 12 V battery projects within that envelope. It is not suitable for driving raw LEDs without additional current limiting. Builders who need more than 5 A peak must choose a higher-rated converter.

Přednosti

  • Boosts voltage from 3.7 V lithium cells to stable 5 V USB power
  • Delivers up to 5 A peak current for demanding automotive projects
  • Integrated XL6019 IC provides over-temperature and over-current protection
  • Operates at 180 kHz switching frequency with up to 94 % efficiency
  • Adjustable 5 V to 45 V output from 3 V to 40 V input range

Specifikace

TypeStep-Up Voltage Regulator
Mounting StyleStand Alone
Current Rating5 A
Power Rating30 W
FeaturesOvercurrent Protection, Reverse Current Protection, Thermal Protection

Otázky k tomuto produktu

Should I pick the 3 A sustained or the 5 A peak rating for my load?

Design for 3 A continuous; the 5 A peak is only for brief transients and the 30 W limit still applies.

What does the 94 % efficiency figure mean when I power a 12 V project from a 3.7 V cell?

It is the best-case conversion rate; actual efficiency drops as the input-to-output voltage gap widens.

How does the 180 kHz switching frequency affect my choice of input capacitor?

The 180 kHz rate keeps ripple below 100 mV, so a standard low-ESR electrolytic or ceramic capacitor at the 3-40 V input is sufficient.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.