Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Green circuit board with dual CAN chips and 40-pin header

LORDWORLD

LORDWORLD 2-Channel Isolated CAN Bus HAT MCP2515 SN65HVD230

SKU CH-QH09-18JF7

Two-channel isolated CAN Bus HAT for Raspberry Pi with dual MCP2515 and SN65HVD230 chips, electrical isolation, TVS and ESD protection, selectable 3.3V or 5V operation and 120Ω termination

  • Dual MCP2515 and SN65HVD230 chips enable reliable 2-channel CAN Bus communication
  • Electrical isolation, SM24CANB TVS diode and ESD protection give safe anti-interference performance
  • Onboard jumpers select 3.3V or 5V operating voltage and 120 terminal resistor
  • Integrated power isolation, transient peak voltage protection and signal isolation secure communication
  • Fits Raspberry Pi 40PIN GPIO header with C/Python examples and manual for quick setup

Dual-Channel Isolated CAN HAT for Raspberry Pi

This LORDWORLD expansion board adds two independent CAN Bus channels to any Raspberry Pi with a 40-pin GPIO header. It uses an MCP2515 controller and SN65HVD230 transceiver on each channel to provide reliable communication for automotive, industrial or robotics projects.

Makers needing dual isolated CAN interfaces

Developers who require CAN FD support, higher throughput or more than two channels will need a different solution. The board is not suited for systems without a 40-pin Raspberry Pi header or for applications that demand onboard processing beyond CAN framing.

MCP2515 and SN65HVD230 dual-chip architecture

Each channel pairs an MCP2515 controller with an SN65HVD230 transceiver behind electrical isolation, a SM24CANB TVS diode and ESD protection. Onboard jumpers select 3.3 V or 5 V logic and enable or disable the 120 Ω termination resistor. C and Python examples plus a manual are included.

Přednosti

  • Dual MCP2515 and SN65HVD230 chips enable reliable 2-channel CAN Bus communication
  • Electrical isolation, SM24CANB TVS diode and ESD protection give safe anti-interference performance
  • Onboard jumpers select 3.3V or 5V operating voltage and 120 terminal resistor
  • Integrated power isolation, transient peak voltage protection and signal isolation secure communication
  • Fits Raspberry Pi 40PIN GPIO header with C/Python examples and manual for quick setup

Specifikace

BrandLORDWORLD

Otázky k tomuto produktu

Should I pick the 3.3V or 5V jumper setting for my Raspberry Pi?

Select 3.3V to match the Pi GPIO logic level; choose 5V only if your external CAN device requires 5V signalling.

What does the 2-channel MCP2515 and SN65HVD230 design actually deliver in a live project?

It gives two independent CAN buses on one HAT, each with its own controller and isolated transceiver for simultaneous send and receive.

How does the 120 Ω termination jumper affect the bus in practice?

Enable it on the two end nodes of each CAN line to absorb reflections; leave it off on intermediate nodes to avoid loading the bus.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.