Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Sleeved adapter cable with 14-pin, 10-pin and 24-pin connectors, 63cm long

myVolts

myVolts 14 Pin + 10 Pin to 24 Pin ATX PSU Adapter Cable 63cm

SKU CH-818M-8TN88

Adapts Corsair AXI, HXI, RM (old yellow label) and AX1200 modular PSUs with 14-pin and 10-pin outputs to standard 24-pin motherboard connectors using 18 AWG sleeved cable, 63 cm long

  • TypeAT
  • Converts 14+10 pin PSU to standard 24 pin motherboard
  • 63 cm sleeved cable with 18 AWG copper conductors
  • Self-adhesive tape included for tidy cable routing
  • Designed for Corsair AXI HXI and AX1200 power supplies
  • Only use with listed 14+10 pin modular PSUs

Corsair PSU adapter cable

This 63 cm sleeved adapter converts the 14 pin and 10 pin modular ports on compatible Corsair AXI, HXI and legacy RM or AX1200 power supplies into a standard 24 pin ATX connector for the motherboard. It uses 18 AWG tin-coated copper wire and includes self-adhesive tape for securing the cable run.

Fits Corsair modular PSUs

The cable plugs directly into the 14 pin and 10 pin sockets on the power supply and presents a single 24 pin header for any ATX motherboard, freeing the builder from sourcing a matching Corsair Type 4 cable set. No additional connectors or tools are required beyond the supplied tape.

Replaces missing Type 4 cables

The jump is worth it when a compatible Corsair unit lacks its original 24 pin cable or when repurposing the PSU in a standard ATX build. It is not for power supplies that use a single 24 pin modular port, nor for non-Corsair units where the pin-out differs and damage would result.

Přednosti

  • Converts 14+10 pin PSU to standard 24 pin motherboard
  • 63 cm sleeved cable with 18 AWG copper conductors
  • Self-adhesive tape included for tidy cable routing
  • Designed for Corsair AXI HXI and AX1200 power supplies
  • Only use with listed 14+10 pin modular PSUs

Specifikace

TypeAT

Otázky k tomuto produktu

Will the 18 AWG wires overheat if the 24 pin connector draws full load all day?

The cable uses 1007-18AWG tin-coated copper rated for the current a standard 24 pin motherboard connector can request.

Does the sleeved 63 cm length add noticeable heat or noise inside a closed case?

The adapter is a passive cable with no fan or active components, so it produces no noise and adds negligible heat.

Which power supply must I already own for this 14 pin + 10 pin adapter to work?

It only fits Corsair AXI, HXI, RM (old yellow-label) and AX1200 units that expose both a 14 pin and a 10 pin modular port.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.