Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Rectangular metal power supply unit, silver aluminium case with ventilation slots, terminal block outputs, label showing 12V 20A 250W

myVolts

myVolts AC-DC Switching Power Supply 12V 20A 250W

SKU CH-7QR0-W4HS9

Converts AC mains to 12 V DC at 20 A with built-in over-voltage, over-current and short-circuit protection

  • TypeAT
  • Converts mains AC to stable 12 V DC for reliable equipment power
  • Delivers up to 20 A continuous current for demanding 12 V loads
  • Built-in over-voltage, over-current and short-circuit protection safeguards connected devices
  • Metal enclosure aids heat dissipation for consistent operation
  • Certified to CCC, RoHS and CE standards for safety compliance

12 V 20 A switching supply

This AC-to-DC unit converts 110 V or 220 V mains to a regulated 12 V output rated at 20 A and 250 W. It is built for indoor bench work, test rigs and fixed installations that need a stable 12 V rail. The metal enclosure meets CCC, RoHS and CE marks.

250 W continuous headroom

At full load the supply delivers 20 A continuously while built-in over-voltage, over-current and short-circuit protection guard the output. It operates from 0 °C to 40 °C with humidity up to 95 % non-condensing. Loads above 20 A or sustained ambient temperatures over 40 °C are outside the rated envelope.

AT form-factor compatibility

The supply follows the AT type designation and measures 200 mm by 100 mm by 44 mm with an input range of 110 V or 220 V ± 15 %. Builders using ATX-only mounting holes or needing a different form factor cannot use this unit.

Přednosti

  • Converts mains AC to stable 12 V DC for reliable equipment power
  • Delivers up to 20 A continuous current for demanding 12 V loads
  • Built-in over-voltage, over-current and short-circuit protection safeguards connected devices
  • Metal enclosure aids heat dissipation for consistent operation
  • Certified to CCC, RoHS and CE standards for safety compliance

Specifikace

TypeAT

Otázky k tomuto produktu

Will the 20 A 12 V output run alongside my older 12 V 10 A supply on the same 110 V/220 V circuit?

Both units accept 110 V/220 V AC input, so they can share the same mains circuit. The 20 A model is rated for 250 W and the 10 A model for 120 W.

How can I verify the 250 W unit is delivering a stable 12 V after installation?

Measure the DC output terminals with a multimeter; a reading near 12 V under load confirms the built-in over-voltage, over-current and short-circuit protection is functioning.

Does the package include mounting brackets or a power cord, or must I buy them separately?

The box contains only the power supply unit. Mounting hardware and an AC input cord are not included and must be sourced separately.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.