Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Two green DDR5 RDIMM modules without heat spreaders, 256GB kit

NEMIX RAM

NEMIX RAM DDR5 4800 256GB (2x128GB) CL40 2Rx4 ECC Registered RDIMM Supermicro H14SSF memory upgrade

SKU CH-2TYJ-1TBC4

256 GB kit of two 128 GB DDR5-4800 ECC registered RDIMMs at 1.1 V CL40 for Supermicro H14SSF servers

  • Capacity256GB (2 x 128GB)
  • Type288-Pin DDR5 RDIMM
  • SpeedDDR5 4800 (PC5 38400)
  • CAS LatencyCL40
  • Voltage1.10V
  • ECCYes

Size 256GB 2X128GB

Zobrazit dalších 24 konfigurací
  • 256GB total capacity from two 128GB modules for maximum server memory density
  • DDR5 4800 speed with CL40 latency delivers rated throughput for Supermicro H14SSF
  • Registered ECC architecture offloads the memory controller and corrects single-bit errors automatically
  • 1V operation matches the board's voltage requirement for stable full-population performance
  • 288-pin RDIMM form factor fits the exact slot type the motherboard requires

Capacity and Fit

This 256GB kit (2 x 128GB) provides DDR5-4800 registered ECC memory built specifically for the Supermicro H14SSF motherboard. The 288-pin RDIMM modules match the board’s required form factor, voltage, rank and timing so the system recognises the full capacity at rated speed.

Upgrade Scope

It replaces lower-capacity DDR5 RDIMM kits or fills empty slots when the platform’s memory population rules allow full 256GB operation. The jump is worthwhile when your workloads need the maximum registered ECC capacity this board supports and you have verified the approved DIMM sequence in the manual.

Pre-Install Checks

Confirm the H14SSF firmware revision and the motherboard manual’s qualified vendor list before ordering. Verify the exact slot population order, maximum supported capacity per channel and any BIOS settings required for 2Rx4 registered modules. Ensure the chassis has clearance for standard-height RDIMMs.

Přednosti

  • 256GB total capacity from two 128GB modules for maximum server memory density
  • DDR5 4800 speed with CL40 latency delivers rated throughput for Supermicro H14SSF
  • Registered ECC architecture offloads the memory controller and corrects single-bit errors automatically
  • 1V operation matches the board's voltage requirement for stable full-population performance
  • 288-pin RDIMM form factor fits the exact slot type the motherboard requires

Specifikace

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Server Memory
ModelDDR5 ECC RDIMM Registered Server Memory
Part NumberMR38400-724K2
Capacity256GB (2 x 128GB)
Type288-Pin DDR5 RDIMM
SpeedDDR5 4800 (PC5 38400)
CAS LatencyCL40
Voltage1.10V
ECCYes
Buffered/RegisteredRegistered
Rank2Rx4
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 ECC RDIMM Motherboard Compatible
Package Content256GB 2X128GB DDR5 4800MHz PC5-38400 2Rx4 1.1V 288-PIN ECC RDIMM KIT

Další verze tohoto modelu

Dalších 5 v této řadě

Stejná řada, jiná paměť, chladič nebo takt — porovnejte, než se rozhodnete.

Otázky k tomuto produktu

Does the 288-pin RDIMM form factor match the Supermicro H14SSF motherboard slots?

Yes, this kit uses the 288-pin Registered RDIMM form factor that the Supermicro H14SSF requires; it is not a UDIMM or SODIMM and will seat in the board's DDR5 DIMM slots.

What is the correct population order when installing both 128GB modules in the H14SSF?

Consult the Supermicro H14SSF manual for the approved DIMM population sequence; the board's memory-controller rules dictate which slots must be filled first for dual-rank 2Rx4 modules.

Will the 1.1V DDR5 modules need any firmware updates or battery-backed settings to maintain ECC operation over time?

No firmware or battery maintenance is required for ECC; the registered architecture and on-die ECC function continuously at 1.1V, and the modules carry a lifetime replacement warranty if a hardware fault ever occurs.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.