Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Two green DDR5 RDIMM modules with gold contacts and black chips, no heat spreader

NEMIX RAM

NEMIX RAM DDR5 4800 32GB 2x16GB CL40 1.1V ECC RDIMM Supermicro H13SSH memory upgrade

SKU CH-J17M-GJ4T1

A 32GB dual-module DDR5-4800 ECC RDIMM kit with CL40 timing and 1.1V operation, validated for the Supermicro H13SSH motherboard

  • Capacity32GB (2 x 16GB)
  • Type288-Pin DDR5 RDIMM
  • SpeedDDR5 4800 (PC5 38400)
  • CAS LatencyCL40
  • Voltage1.10V
  • ECCYes

Size 32GB 2X16GB

Zobrazit dalších 30 konfigurací
  • 32 GB kit lets you run fully populated memory channels at rated speed
  • Registered ECC RDIMM architecture offloads the controller and corrects single-bit errors on the fly
  • DDR5 4800 CL40 1.10 V timing matches the Supermicro H13SSH memory controller exactly
  • 288-pin 1Rx8 form factor fits the board's required DIMM slots without adapters
  • Lifetime replacement warranty with free US-based technical support included

Exact-match DDR5 ECC RDIMM kit for Supermicro H13SSH

This 32GB kit contains two 16GB DDR5 4800 RDIMM modules built to the precise 1Rx8 rank, 1.1V voltage and CL40 timing the H13SSH memory controller expects. Registered ECC architecture offloads the controller and corrects single-bit errors on the fly. The 288-pin form factor matches the board's DIMM slots exactly.

Who this suits and who should look elsewhere

Server administrators upgrading a Supermicro H13SSH system that requires registered ECC DDR5 RDIMMs will find this kit validated for full-capacity population. Builders needing unbuffered UDIMMs, SODIMMs, non-ECC memory, or a different DDR generation cannot use these modules.

Build integration: what it needs and what it frees

Installation follows the motherboard manual's approved DIMM population order; no extra cooling or voltage adjustment is required beyond the standard 1.1V spec. Registered buffering lets every slot run fully populated at rated speed, freeing the memory controller from electrical loading while ECC prevents silent data corruption and unplanned reboots in production workloads.

Přednosti

  • 32 GB kit lets you run fully populated memory channels at rated speed
  • Registered ECC RDIMM architecture offloads the controller and corrects single-bit errors on the fly
  • DDR5 4800 CL40 1.10 V timing matches the Supermicro H13SSH memory controller exactly
  • 288-pin 1Rx8 form factor fits the board's required DIMM slots without adapters
  • Lifetime replacement warranty with free US-based technical support included

Specifikace

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Server Memory
ModelDDR5 ECC RDIMM Registered Server Memory
Part NumberMR38400-618K2
Capacity32GB (2 x 16GB)
Type288-Pin DDR5 RDIMM
SpeedDDR5 4800 (PC5 38400)
CAS LatencyCL40
Voltage1.10V
ECCYes
Buffered/RegisteredRegistered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 ECC RDIMM Motherboard Compatible
Package Content32GB 2X16GB DDR5 4800MHz PC5-38400 1Rx8 1.1V 288-PIN ECC RDIMM KIT

Další verze tohoto modelu

Dalších 5 v této řadě

Stejná řada, jiná paměť, chladič nebo takt — porovnejte, než se rozhodnete.

Otázky k tomuto produktu

Does the Supermicro H13SSH motherboard need an available 288-pin DDR5 RDIMM slot for this kit?

Yes, the kit uses the 288-pin DDR5 RDIMM form factor that the H13SSH requires, so at least one compatible slot must be free.

Can I mix these 1Rx8 CL40 1.1V modules with existing DDR5 RDIMMs of a different rank or speed on the same board?

Mixing different ranks or speeds is not recommended; the H13SSH memory controller expects matched modules for stable operation at 4800 MT/s.

How can I confirm the system recognises the full 32 GB at 4800 MT/s with ECC active after installation?

Check the BIOS memory summary or run a tool such as dmidecode; it should show 32 GB total, 4800 MT/s, and ECC enabled for each DIMM.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.