Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Green circuit board with black memory chips, 288 gold pins, no heat spreader

NEMIX RAM

NEMIX RAM DDR5 ECC RDIMM 16GB 4800MHz CL40 1Rx8 1.1V Supermicro H13SSH-E memory upgrade

SKU CH-RZB1-FEE2G

16 GB DDR5-4800 ECC registered RDIMM, CL40 at 1.1 V, 1Rx8 layout validated for Supermicro H13SSH-E motherboards

  • Capacity16GB
  • Type288-Pin DDR5 RDIMM
  • SpeedDDR5 4800 (PC5 38400)
  • CAS LatencyCL40
  • Voltage1.10V
  • ECCYes

Size 16GB

Zobrazit dalších 30 konfigurací
  • Exact 16 GB DDR5-4800 match for Supermicro H13SSH-E runs at rated speed
  • Registered ECC architecture offloads controller for full-slot stability
  • 1 V CL40 1Rx8 timing recognised by memory controller without downclocking
  • 288-pin RDIMM form factor fits the board's required slot type
  • Lifetime replacement warranty with US-based technical support included

Exact-match DDR5 server upgrade

This 16 GB DDR5-4800 RDIMM is built for the Supermicro H13SSH-E motherboard. Registered ECC architecture and CL40 timing match the board's memory controller so the module is recognised at full capacity and rated speed. The 1Rx8 organisation and 1.1 V operation follow the platform's population rules without adaptation.

Thermals and power in normal use

Operating at 1.1 V keeps power draw low across every populated slot. The registered design buffers address and command signals, reducing electrical load on the memory controller during sustained workloads. No heat spreader is fitted, so airflow across the bare PCB handles thermal dissipation in standard server chassis.

Build quality and daily implications

Major OEM DRAM from Samsung, Micron or Hynix underpins the lifetime replacement warranty and free US-based technical support. The 288-pin RDIMM keying prevents accidental insertion into UDIMM or SODIMM slots, while ECC corrects single-bit errors before they reach production data. Verify your system manual for approved DIMM population order and maximum supported capacity before installation.

Přednosti

  • Exact 16 GB DDR5-4800 match for Supermicro H13SSH-E runs at rated speed
  • Registered ECC architecture offloads controller for full-slot stability
  • 1 V CL40 1Rx8 timing recognised by memory controller without downclocking
  • 288-pin RDIMM form factor fits the board's required slot type
  • Lifetime replacement warranty with US-based technical support included

Specifikace

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Server Memory
ModelDDR5 ECC RDIMM Registered Server Memory
Part NumberMR38400-618K1
Capacity16GB
Type288-Pin DDR5 RDIMM
SpeedDDR5 4800 (PC5 38400)
CAS LatencyCL40
Voltage1.10V
ECCYes
Buffered/RegisteredRegistered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 ECC RDIMM Motherboard Compatible
Package Content16GB DDR5 4800MHz PC5-38400 1Rx8 1.1V 288-PIN ECC RDIMM KIT

Další verze tohoto modelu

Dalších 5 v této řadě

Stejná řada, jiná paměť, chladič nebo takt — porovnejte, než se rozhodnete.

Otázky k tomuto produktu

How do I install this 288-pin DDR5 RDIMM in the Supermicro H13SSH-E and which slot order does the manual require?

Power down the server, open the chassis, and insert the module into the DIMM slots following the population sequence shown in the Supermicro H13SSH-E manual; the registered 288-pin form factor keys only one way, so align the notch before pressing firmly until the ejectors click.

Will the ECC registered RDIMM need any firmware updates or component swaps during its service life?

The module itself has no user-serviceable parts; ECC corrects single-bit errors automatically, and the registered buffer requires no firmware. Replace the DIMM only if the system logs uncorrectable errors or a slot fails.

What thermal or electrical limit appears first when this 1.10 V CL40 kit runs at 4800 MT/s under continuous load?

The JEDEC-rated 1.10 V operating voltage and CL40 timing define the electrical envelope; sustained full-speed operation stays within that spec, so the first limit encountered is the motherboard's maximum supported capacity per channel rather than a module thermal threshold.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.