Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Four black DDR2 UDIMM modules in a kit

OWC

OWC 4GB (4x1GB) DDR2 533 PC2-4200 CL4 1.8V Non-ECC UDIMM Kit

SKU CH-N3A3-ADBP3

Four 1 GB DDR2 533 modules run at CL4 latency and 1.8 V for desktop upgrades

  • Capacity4GB (4 x 1GB)
  • SpeedDDR2 533 (PC2 4200)
  • CAS LatencyCL4
  • Voltage1.8V
  • ECCNo
  • Buffered/RegisteredUnbuffered

Capacity 4GB (4 x 1GB)

  • 4GB total capacity from four 1GB modules
  • DDR2 533 speed with CL4 latency for responsive operation
  • 8V JEDEC standard voltage ensures broad desktop compatibility
  • Unbuffered non-ECC design suited for consumer desktop boards
  • 240-pin UDIMM form factor fits standard DDR2 slots

OWC DDR2 533 4GB Kit

This OWC kit provides four 1 GB DDR2 533 modules for a total of 4 GB. It is built as an unbuffered non-ECC upgrade for desktop systems that accept 240-pin DIMMs. Each module runs at the standard 1.8 V JEDEC voltage and carries a CL4 latency rating. The kit targets users who need a straightforward capacity increase on older platforms.

Sustained load behaviour

JEDEC-compliant DDR2 533 modules maintain their rated 533 MT/s data rate and CL4 timing during extended use because they operate at the specified 1.8 V without overclocking. The unbuffered design adds no extra register delay, so latency stays consistent across long sessions. ROHS-compliant components and OWC in-house validation reduce the risk of thermal throttling or errors over time.

Deciding specification

The critical figure is the DDR2 533 (PC2-4200) speed rating combined with the 240-pin form factor. A motherboard must explicitly support DDR2 533 unbuffered non-ECC DIMMs at 1.8 V for these modules to function. If the board requires a different DDR generation, a higher voltage, or registered memory, this kit will not be compatible.

Přednosti

  • 4GB total capacity from four 1GB modules
  • DDR2 533 speed with CL4 latency for responsive operation
  • 8V JEDEC standard voltage ensures broad desktop compatibility
  • Unbuffered non-ECC design suited for consumer desktop boards
  • 240-pin UDIMM form factor fits standard DDR2 slots

Specifikace

BrandOWC
Part Number4U2D21R8004S
Capacity4GB (4 x 1GB)
SpeedDDR2 533 (PC2 4200)
CAS LatencyCL4
Voltage1.8V
ECCNo
Buffered/RegisteredUnbuffered
Multi-channel KitDual Channel Kit
ColorBlack
Heat SpreaderNo
Recommend UseDesktops
LED ColorNone

Další verze tohoto modelu

Dalších 4 v této řadě

Stejná řada, jiná paměť, chladič nebo takt — porovnejte, než se rozhodnete.

Otázky k tomuto produktu

How much heat will the four 1.8 V DDR2 modules generate during continuous all-day use?

Each module runs at the standard 1.8 V JEDEC voltage for DDR2 533, so heat output is typical for unbuffered desktop DIMMs; the kit has no heat spreaders, so case airflow is the main cooling path.

What must the desktop already provide to accept this 240-pin UDIMM kit?

The system needs four free 240-pin DDR2 slots that support 1.8 V unbuffered non-ECC memory and dual-channel operation for the matched 4 x 1 GB configuration.

Will the CL4 533 MHz sticks down-clock automatically if the motherboard only supports slower DDR2 speeds?

Yes — JEDEC-compliant DDR2 modules negotiate the highest common speed with the memory controller, so they will run at the board's maximum supported rate without manual setup.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.