Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
A 100 mm four-wire cable with black JST SH connectors on both ends

Adafruit

Adafruit STEMMA QT Qwiic JST SH 4-pin Cable 100mm

SKU CH-N4KC-0Z69A

A 100 mm JST SH cable with 4-pin connectors links STEMMA QT or Qwiic boards for sensor and driver connections

  • TypePrototyping Products
  • Connect sensors instantly with 100mm flexible cable
  • Secure 1mm pitch JST SH connectors lock firmly
  • Symmetrical design eliminates wrong-side insertion errors
  • Colour-coded wires simplify 3.3V power and I2C data routing
  • Ready for Qwiic boards and STEMMA QT devices

Connection Cable for Prototyping

This 100 mm cable links STEMMA QT and Qwiic boards using 4-pin JST SH connectors on both ends. The 1 mm pitch design keeps the assembly compact while maintaining a secure latch. Symmetrical wiring means either connector can attach to the sensor or the controller without orientation concerns.

Verify Board Headers Before Ordering

Confirm that both devices expose a 4-pin JST SH header with the standard pinout. The cable carries power, ground and I²C data lines in a fixed colour sequence. Mismatched pin assignments or a different pitch connector will prevent the link from functioning.

Colour-Coded Wires Simplify Wiring

Red, black, blue and yellow conductors map directly to 3.3 V power, ground, SDA and SCL respectively. This labelling removes guesswork when debugging the bus. No additional adapters or software are required to use the cable with compatible boards.

Kohokohdat

  • Connect sensors instantly with 100mm flexible cable
  • Secure 1mm pitch JST SH connectors lock firmly
  • Symmetrical design eliminates wrong-side insertion errors
  • Colour-coded wires simplify 3.3V power and I2C data routing
  • Ready for Qwiic boards and STEMMA QT devices

Tekniset tiedot

TypePrototyping Products

Kysymyksiä tästä tuotteesta

What comes with the 100mm STEMMA QT cable and do I need any extra headers or boards?

The cable is a single 4-wire lead with JST-SH female connectors on both ends; no additional headers, boards or accessories are included.

How do I pick between the STEMMA QT and Qwiic ends on this cable?

Both connectors are identical JST-SH 4-pin plugs wired for 3.3 V power, ground, SDA and SCL, so either end can mate with any STEMMA QT or Qwiic port.

What do the 3.3 V power and I2C lines do once the cable is plugged into a microcontroller board?

Red carries 3.3 V supply, black is ground, blue carries I2C SDA data and yellow carries I2C SCL clock, letting the host talk to the attached sensor or driver.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.