HyperX FURY 16GB (2 x 8GB) DDR3 1866 CL10 HX318C10FK2/16
- 16GB (2 x 8GB)
- DDR3 1866 (PC3 1490…
Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.
HyperX
8GB DDR3 desktop module running at 1866MHz with CL10 timing and a blue asymmetric heat spreader
Capacity 8GB
This HyperX FURY module is an 8GB DDR3 desktop memory kit rated for 1866MHz speed. It operates at a standard 1.50V voltage with CL10 latency timings of 10-11-10. The blue asymmetric heat spreader aids thermal dissipation for stable operation.
This unbuffered, non-ECC DIMM fits standard desktop motherboards with DDR3 slots supporting 1866MHz speeds. It works with compatible Intel and AMD platforms using JEDEC standard voltages. Systems requiring ECC, registered memory, or a different DDR generation should select an alternative module.
The decisive specification is the DDR3 1866MHz speed combined with CL10 timing at 1.50V. Verify your motherboard supports this frequency and voltage before purchase. Automatic overclocking functionality simplifies installation for plug-and-play performance.
| Brand | HyperX |
|---|---|
| Series | FURY |
| Model | HX318C10F/8 |
| Capacity | 8GB |
| Speed | DDR3 1866 |
| CAS Latency | CL10 |
| Timing | 10-11-10 |
| Voltage | 1.50V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Color | Blue |
| Heat Spreader | Yes |
| Features | JEDEC standard 1.5V (1.425V ~ 1.575V) Power Supply VDDQ = 1.5V (1.425V ~ 1.575V) 933 MHz fCK for 1866 MB/sec/pin 8 independent internal bank Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6 Programmable Additive Latency: 0, CL - 2, or CL - 1 clock 8-bit pre-fetch Burst Length: 8 (Interleave without any limit, sequential with starting address "000" only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] Bi-directional Differential Data Strobe Internal(self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm +/- 1%) On Di |
| Lähetyspaino | 0.05 kg |
| Pakkauksen mitat | 151 × 56 × 14 mm |
Tämän mallin muut versiot
Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.
Yes, it is an unbuffered DIMM built to the JEDEC 1.5 V standard, so it installs in any desktop DDR3 slot that accepts 1866 MHz memory.
They show CAS latency of 10 cycles with 11-cycle RAS-to-CAS and RAS precharge delays, giving low access latency at the rated 1866 MHz data rate.
The module supports JEDEC 1.5 V operation (1.425 V–1.575 V range); 1.35 V is not a validated voltage for this part.
Myös tällä osastolla
Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.
Valuutta, jolla maksetaan, sekä valuutta, jossa hinnat näytetään.
Lähetetään lompakostasi kassalla
Vain näyttöä varten — hinnat ovat Yhdysvaltain dollareissa
Valuuttaa ei löytynyt.
Valitse kieli, jolla sivusto puhuu sinulle.
Uusi täällä?
Onko sinulla jo tili?
Automaattista palautusta ei ole: kauppa ei lähetä sähköpostia lainkaan, joten kertakäyttöistä linkkiä ei ole mistä pyytää. Jätä osoite tilille, niin se käsitellään käsin.
Pyyntö kirjattu
Mikään ei ole tulossa sähköpostiisi — tämä kauppa ei lähetä sähköpostia lainkaan. Joku käsittelee nämä pyynnöt käsin.
Muistitko sen?