Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Two green circuit boards with gold contacts and black memory chips side by side

NEMIX RAM

NEMIX RAM 96GB 2x48GB DDR5 5600 CL46 1.1V 2Rx8 ECC RDIMM GIGABYTE MZ73-LM1 memory upgrade

SKU CH-045P-PWNJM

A 96 GB DDR5 registered ECC kit built for the Gigabyte MZ73-LM1 server motherboard

  • Capacity96GB (2 x 48GB)
  • Type288-Pin DDR5 RDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCYes

Size 96GB 2X48GB

Näytä 24 muuta kokoonpanoa
  • 96 GB capacity with two 48 GB modules for full population
  • DDR5 5600 speed matches the motherboard's rated frequency
  • CL46 CAS latency and 1.1 V voltage meet the controller's timing spec
  • 2Rx8 registered ECC RDIMM architecture enables error correction and signal buffering
  • Verified fitment for the GIGABYTE MZ73-LM1 motherboard's 288-pin RDIMM slots

Exact-Match DDR5 ECC Kit for GIGABYTE MZ73-LM1

This 96GB kit contains two 48GB DDR5-5600 Registered ECC RDIMMs built to the precise rank, voltage and timing the GIGABYTE MZ73-LM1 memory controller expects. The modules are recognized at full capacity and run at their rated speed without manual tuning. It is intended for server administrators who need guaranteed compatibility with this specific motherboard.

Registered Architecture

Registered buffering offloads the memory controller so every slot runs fully populated at full capacity while ECC corrects single-bit errors on the fly. The 288-pin RDIMM form factor is the only type this board accepts; UDIMM or SODIMM modules will not fit. No heat spreader is included, so airflow in the chassis must be sufficient for sustained operation.

CL46 Latency at 1.1V Defines the Correct Part

The single specification that decides fitment is CAS latency 46 at 1.1V combined with 2Rx8 Registered ECC DDR5-5600. If your system requires a different latency, voltage, rank or buffering type this kit will not work. Consult the motherboard manual for supported capacities and approved DIMM population order before purchase.

Kohokohdat

  • 96 GB capacity with two 48 GB modules for full population
  • DDR5 5600 speed matches the motherboard's rated frequency
  • CL46 CAS latency and 1.1 V voltage meet the controller's timing spec
  • 2Rx8 registered ECC RDIMM architecture enables error correction and signal buffering
  • Verified fitment for the GIGABYTE MZ73-LM1 motherboard's 288-pin RDIMM slots

Tekniset tiedot

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Server Memory
ModelDDR5 ECC RDIMM Registered Server Memory
Part NumberMR44800-4828K2
Capacity96GB (2 x 48GB)
Type288-Pin DDR5 RDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCYes
Buffered/RegisteredRegistered
Rank2Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemGIGABYTE
FeaturesDDR5 ECC RDIMM Motherboard Compatible
Package Content96GB 2X48GB DDR5 5600MHz PC5-44800 2Rx8 1.1V 288-PIN ECC RDIMM KIT

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

What speed does the DDR5 5600 PC5-44800 interface actually run at in this kit?

The modules operate at DDR5 5600 (PC5-44800) with a CAS latency of CL46, delivering the rated transfer rate when installed in a compatible system.

What physical slot and form factor does this 288-pin RDIMM kit require on the GIGABYTE MZ73-LM1 motherboard?

It uses standard 288-pin DDR5 RDIMM slots; the board must accept registered DIMMs, not UDIMM or SODIMM, and the two 48 GB modules populate the supported DIMM sockets.

How do I install the 2Rx8 registered ECC modules and which population order avoids a common mistake?

Power down, open the chassis, align each 288-pin RDIMM with the keyed slot, press firmly until the latches lock, then follow the motherboard manual's exact DIMM population sequence for dual-rank registered memory.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.