Nous acceptons la cryptomonnaie — les cryptos que vous détenez peuvent ainsi acheter du matériel réel.Payez en crypto, dépensez-la en matériel réel. Livraison assurée offerte partout dans le monde au-delà de 399 $. Cartons neutres, sans marque, expédiés depuis l’Allemagne.Livraison assurée offerte au-delà de 399 $. Votre taux est bloqué pendant 30 minutes dès l’ouverture de la caisse.Taux bloqué 30 minutes. Chaque article est scellé, son numéro de série est vérifié, et il est couvert par une garantie de 24 mois.Scellé, garanti 24 mois.

Articles suivis Se connecter
Green printed circuit board with two microcontroller chips, a rectangular metal shell, and two double-ended USB-C cables

MCDODO

MCDODO MAKCM V2 ESP32-S3 Dev Board DMA 1000Hz 2 Cables

SKU CH-ERZ5-SQ7K0

ESP32-S3 development board with dual chips, CH343 UART at 4 Mbps, pre-flashed Full-Pass v3 firmware for 1000 Hz polling, supplied in a button-enabled shell with two double-ended USB cables

  • TypeSingle Board Computers
  • Dual ESP32-S3 chips enable parallel processing
  • CH343 UART controller delivers 4Mbps zero-latency transfer
  • Pre-flashed Full-Pass v3 firmware runs instantly
  • Button-enabled shell simplifies physical interaction
  • Two double-ended USB cables connect directly

Dual ESP32-S3 development board

This board pairs two ESP32-S3 chips with a CH343 UART controller to deliver 4 Mbps transfers at a 1000 Hz polling rate. It targets makers and engineers building low-latency input devices or edge-computing prototypes that need dual-core Wi-Fi and Bluetooth 5 connectivity. The pre-flashed Full-Pass v3 firmware provides immediate mouse-simulation capability without additional toolchain setup.

Headroom at 4 Mbps and 1000 Hz

The dual-chip architecture sustains the rated 4 Mbps link with zero-latency UART signalling, so high-frequency HID streams and real-time sensor fusion run without throttling. Workloads that exceed the 32 GPIOs or require more than two concurrent USB endpoints will hit the silicon limits, and the single UART channel cannot serve additional high-speed peripherals simultaneously.

Button-enabled shell and twin cables

A moulded shell with an integrated tactile button lets developers trigger firmware events or mode switches without soldering headers. Two double-ended USB-C cables are included, removing the need to source matching leads for power, flashing and host communication during bring-up. No extra software utilities or configuration files are bundled beyond the factory firmware image.

Points forts

  • Dual ESP32-S3 chips enable parallel processing
  • CH343 UART controller delivers 4Mbps zero-latency transfer
  • Pre-flashed Full-Pass v3 firmware runs instantly
  • Button-enabled shell simplifies physical interaction
  • Two double-ended USB cables connect directly

Caractéristiques

TypeSingle Board Computers

Questions sur cet article

Will the MAKCM V2 board work with my older USB 2.0 hubs and ports?

The board includes a CH343 UART controller that transfers data at 4Mbps over USB. It uses the two double-ended USB-C cables supplied, so it will connect to any USB host that accepts a USB-C plug.

How can I verify the 1000Hz polling rate is active after I flash the board?

The unit ships pre-flashed with Full-Pass v3 firmware that targets 1000Hz polling. You can confirm the rate in your operating system mouse settings or with a USB polling-rate test utility.

The listing mentions two double-ended USB-C cables and a button-enabled shell — is anything else required to start developing?

The package contains the PCB, the shell with integrated button, and the two double-ended USB-C cables. No extra cables or programmers are needed; just connect to a host PC and begin.

Également dans ce rayon

Les clients ont aussi comparé

Même rayon, même caisse — huit monnaies et un taux bloqué 30 minutes.