Nous acceptons la cryptomonnaie — les cryptos que vous détenez peuvent ainsi acheter du matériel réel.Payez en crypto, dépensez-la en matériel réel. Livraison assurée offerte partout dans le monde au-delà de 399 $. Cartons neutres, sans marque, expédiés depuis l’Allemagne.Livraison assurée offerte au-delà de 399 $. Votre taux est bloqué pendant 30 minutes dès l’ouverture de la caisse.Taux bloqué 30 minutes. Chaque article est scellé, son numéro de série est vérifié, et il est couvert par une garantie de 24 mois.Scellé, garanti 24 mois.

Articles suivis Se connecter
Small ceramic cylinder 6.35mm diameter 20mm long with 100cm wire lead

ProTechTrader

ProTechTrader 12V 40W 6.35mm Ceramic Cartridge Heater MK10 3d printers accessory

SKU CH-A4ZC-XA3T1

12V 40W ceramic cartridge heater with 6.35mm diameter and 20mm length fits MK10 extruders on Wanhao Duplicator i3, FlashForge Creator and Monoprice Maker Select printers

  • 12 V 40 W output gives fast heat-up for MK10 hot-ends
  • 35 mm diameter matches standard 1/4 in heater-block bores
  • 20 mm cartridge length fits common MK10 extruder housings
  • 100 cm wire allows flexible routing to controller boards
  • Compatible with Wanhao Duplicator i3 and FlashForge Creator printers

Ceramic Cartridge Heater MK10

This ProTechTrader ceramic cartridge heater supplies 40 watts at 12 volts for MK10 extruders. It has a 6.35 millimetre diameter and a 20 millimetre length with a 100 centimetre wire lead. The part is designed as a direct OEM fit for printers that use a 1/4 inch heater block bore. It is sold new as a single replacement component.

Compatibility and limits

The heater fits Wanhao Duplicator i3, FlashForge Creator and Monoprice Maker Select v1, v2 and v2.1 machines that have a 1/4 inch heater hole. Printers with a different bore size, a different voltage requirement or a non-MK10 hotend will not accept this cartridge. Buyers who need a higher wattage, a different diameter or a shorter wire length should look at something else.

Pre-installation checks

Verify that your hotend block has a 6.35 millimetre bore and that the printer runs a 12 volt heater circuit. Confirm the existing cartridge measures 20 millimetres in length so the replacement seats fully. Ensure the 100 centimetre wire reach suits your cable routing and that the connector type matches your control board.

Points forts

  • 12 V 40 W output gives fast heat-up for MK10 hot-ends
  • 35 mm diameter matches standard 1/4 in heater-block bores
  • 20 mm cartridge length fits common MK10 extruder housings
  • 100 cm wire allows flexible routing to controller boards
  • Compatible with Wanhao Duplicator i3 and FlashForge Creator printers

Caractéristiques

BrandProTechTrader
Modelch12v40w-25

Questions sur cet article

What voltage and wattage must my printer's power supply provide for this 12V 40W cartridge heater?

The heater requires a 12 volt supply capable of delivering 40 watts, so check that your printer's board and PSU can provide that power on the hot-end output.

Will this 6.35mm diameter heater fit the bore in my MK10 hot-end block?

Yes, it is made for MK10 extruders with a 6.35 mm (1/4 inch) heater-block bore, matching printers such as Wanhao Duplicator i3 and FlashForge Creator.

How can I verify the heater is working correctly after installation?

Heat the hot-end to your normal printing temperature and confirm it reaches and holds that temperature without thermal runaway errors or excessive overshoot.

Également dans ce rayon

Les clients ont aussi comparé

Même rayon, même caisse — huit monnaies et un taux bloqué 30 minutes.