RIMLANCE
RIMLANCE RUD23400S8C2K16-1 16GB (2x8GB) DDR4 2933 CL21 desktop RAM
Dual-channel 16 GB DDR4 kit at 2933 MT/s with CL21 latency and 1.2 V operation
- Capacity16GB (2 x 8GB)
- SpeedDDR4 2933 (PC4 23400)
- CAS LatencyCL21
- ECCNo
- Buffered/RegisteredUnbuffered
- ChipsetMajor Brand Chipset
- Dual-channel 16 GB kit speeds multitasking
- 2933 MHz DDR4 data rate lifts throughput
- CL21 latency keeps response tight
- 2 V operation reduces power draw
- Plug-and-play install needs no BIOS tweaks
16GB DDR4 2933 kit for desktop builds
This 16GB kit contains two 8GB unbuffered DDR4 DIMMs rated at 2933 MT/s with CL21 latency. It is intended for standard desktop motherboards that accept UDIMM modules and need a straightforward capacity increase for everyday multitasking and office workloads.
Step up from 8GB or slower DDR4 when multitasking
Replacing a single 8GB stick or a lower-speed kit with this dual-channel 16GB set adds bandwidth and eliminates capacity bottlenecks. The jump is worthwhile when current memory usage regularly hits the limit during typical productivity tasks or light content creation.
Verify DDR4 UDIMM slots
Confirm the motherboard has two free DDR4 UDIMM slots and supports 1.2 V modules at 2933 MT/s or will down-clock automatically. The kit is non-ECC and unbuffered, so it will not work in platforms that require registered or ECC memory.
Points forts
- Dual-channel 16 GB kit speeds multitasking
- 2933 MHz DDR4 data rate lifts throughput
- CL21 latency keeps response tight
- 2 V operation reduces power draw
- Plug-and-play install needs no BIOS tweaks
Caractéristiques
| Brand | RIMLANCE |
|---|---|
| Model | RUD23400S8C2K16-1 |
| Capacity | 16GB (2 x 8GB) |
| Speed | DDR4 2933 (PC4 23400) |
| CAS Latency | CL21 |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major Brand Chipset |
Questions sur cet article
Will this 288-pin UDIMM fit my standard desktop DDR4 motherboard slots?
Yes, the kit uses the standard 288-pin UDIMM form factor for DDR4 desktop memory, so it fits any consumer board with DDR4 DIMM slots.
What is the correct way to seat both 8 GB sticks so the board runs at 2933 MHz CL21?
Insert each module into the same-coloured slots for dual-channel operation, press down firmly until the side clips click, then enable the XMP or DOCP profile in BIOS to reach 2933 MHz CL21.
Do these 1.2 V modules need any active cooling or periodic replacement?
No, they run at the standard 1.2 V without heatsinks or fans, and solid-state DRAM has no moving parts, so no maintenance or scheduled replacement is required.
Également dans ce rayon
Les clients ont aussi comparé
Même rayon, même caisse — huit monnaies et un taux bloqué 30 minutes.
PrimoChill
PrimoChill Praxis Wetbench Open-Air Test Bench 461.8mm
- Open-Air
274,89 $US
0.00355854BTC
En stock
Silverstone Technology
SilverStone Technology Strider 1200W 80 Plus Platinum Modular Power Supply
- ATX Mid Tower
- 1200W
324,03 $US
0.00419467BTC
En stock