BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
Prihvaćamo kriptovalute — tako kriptovalute koje posjedujete mogu kupiti pravi hardver.Plaćajte kriptovalutom, trošite je na pravi hardver. Besplatna osigurana dostava diljem svijeta iznad 399 $. Obični vanjski kartoni bez oznaka, otpremaju se iz Njemačke.Besplatna osigurana dostava iznad 399 $. Vaš je tečaj blokiran 30 minuta od otvaranja blagajne.Tečaj blokiran 30 minuta. Svaki je artikl zapečaćen, njegov serijski broj provjeren, i pokriven jamstvom od 24 mjeseca.Zapečaćen, jamstvo 24 mjeseca.
OWC
8GB DDR3L 1600 CL11 1.35V 204-pin SODIMM laptop memory upgrade compatible with NCR part numbers 497-0506041, 497-0514577, 7702-K138 and 7761-K131
This 8GB DDR3L module runs at 1600 MHz with CL11 latency and 1.35 V operation. It uses a 204-pin SO-DIMM form factor and is unbuffered non-ECC memory. The part is listed as a direct replacement for NCR part numbers 497-0506041, 497-0514577, 7702-K138 and 7761-K131.
Builders whose hardware requires DDR3L at 1.35 V and a 204-pin slot can use this module. It is not for systems that need registered or ECC memory, nor for platforms that only accept 1.5 V DDR3. Buyers who need a higher capacity per slot or a different pin layout should look elsewhere.
The single specification that decides fit is the 1.35 V operating voltage combined with DDR3L 1600 speed. If the target device specifies 1.5 V DDR3 only, this module will not be compatible. Confirm the system documentation calls for DDR3L 1.35 V before purchase.
| Brand | OWC |
|---|---|
| Part Number | 1S6T32R808GB |
| Capacity | 8GB |
| Type | 204-Pin DDR3 SO-DIMM |
| Speed | DDR3L 1600 (PC3L 12800) |
| CAS Latency | CL11 |
| Voltage | 1.35V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Heat Spreader | No |
| Recommend Use | Laptops, All-in-One Systems, and NAS Systems |
Yes, the module is built to the JEDEC-standard 204-pin DDR3L form factor and matches the NCR part numbers 497-0506041, 497-0514577, 7702-K138 and 7761-K131.
Align the notch with the slot key, insert at an angle, then press down evenly until both side clips snap into place — forcing one side first often bends the retention arm.
No firmware or battery is involved; the module is a passive JEDEC-compliant DDR3L device, so only a future capacity upgrade would replace it.
Također u ovoj kategoriji
Ista polica, ista blagajna — osam valuta i blokada tečaja na 30 minuta.
Ono što šaljete, i ono u čemu gledate cijene.
Poslano iz Vašeg novčanika na blagajni
Samo prikaz — katalog je izražen u dolarima
Nijedna valuta ne odgovara.
Odaberite jezik na kojem Vam se stranica obraća.
Nema odgovarajućeg jezika.
Novi ste ovdje?
Već imate račun?
Ne postoji automatsko resetiranje: ova trgovina ne šalje e-poštu, stoga ne postoji jednokratna poveznica koju biste mogli zatražiti. Ostavite adresu uz svoj račun, netko će je ručno obraditi.
Zahtjev zaprimljen
Ništa neće stići u Vaš pretinac e-pošte — ova trgovina uopće ne šalje e-poštu. Netko će to ručno preuzeti.
Sjetili ste se?